Registruokitės, kad atrakintumėte savo išskirtines B2B kainas ir pradėtumėte apsipirkinėti. Užsiregistruokite dabar!
Universal dimmer switch, Power MOSFET up to 800W image 1

Universal dimmer switch, Power MOSFET up to 800W

Yra sandėlyje: Ne Pardavėjo atsargos: Ne Minimalus užsakymo kiekis: 1
Kaina (be PVM):
65,36 €
Ši kaina galioja iki 31.12.24
EAN: 4010312109656
MPN: 21100810
Pakuotė: 1

Technical Information

Prekės būklė Nauja
Gamintojo pavadinimas Universal dimmer switch, Power MOSFET up to 800W
Prekės ženklas ELTAKO
Kategorijos Jungikliai
Kilmės šalis CN
Suderintos sistemos kodas 8536 5080 00
Kompleksinio bloko išdėstymas Kita
Veikimo metodas Prisilietimo valdymo mygtukas
Dažnio diapazonas 50 Hz
Apkrovos tipas Universalus
Nominali įtampa nuo / iki 230 V
Įrenginio plotis 36 mm
Įrenginio aukštis 58 mm
Įrenginio gylis 66 mm
Maks. perjungimo maitinimo šviesos diodas 800 W

Pakavimo informacija

Pakavimo lygis 1 4010312109656, 4010312109656
Pakavimo lygis 2 4010312109656

Kiti techniniai duomenys

Montavimo metodas DRA
Spalva Mėlynas
Be halogeno Yes
Jungties tipas Prisukamas gnybtas
Paviršiaus apdorojimas Kita
Medžiagos kokybė Termoplastikas
Medžiaga Plastikinis
Tvirtinimo tipas Skyriklio montavimas
Šviesos vertės atmintis Yes
Pastotės įvestis No
Nuoseklioji užtamsinimo sistema No
Naudotinas su judesio davikliu No
Naudotinas su perdavimo mygtuku No
Naudotinas su infraraudonųjų spindulių mygtuku No
Naudotinas su buvimo rodmeniu No
Naudotinas su mygtuku Yes
Naudotinas su laiko jungikliu / laikmačiu No
Kontrolinė įtampa nuo / iki 8-230 V
Permatomas No
Paviršiaus tipas Kilimėlis
Šerdies kryžminė sekcija nuo / iki 6 mm²
Galimas IFTTT palaikymas No
Neryškus fazės nutrūkimas Yes
Neryškus fazės dalijimas Yes
App valdymas per Bluetooth No
Vardinės galios apkrova 800 W
Nominalios galios indukcinė apkrova 800 VA
Nominalios galios talpinė apkrova 800 VA
Suderinamas su Apple HomeKit No
Suderinamas su Google Assistant No
Suderinamas su Amazon Alexa No

Atsisiuntimai

Aprašymas

Universal dimmer switch with rotary knob, Power MOSFET up to 800W. Automatic lamp ­detection. Standby loss 0.2 watt only. With adjustable minimum and maximum brightness. Modular device for DIN EN 60715 TH35 rail mounting. 2 modules = 36mm wide, 58mm deep. Universal dimmer switch for lamps up to 800W, depending on ventilation conditions, dimmable 230V LED lamps and dimmable energy saving lamps (ESL) are also dependent on the lamp electronics and the dimming technology. Up to 3600W with capacity enhancers LUD12 at the terminals X1 and X2. Zero passage switching with soft start and soft OFF to protect lamps. Universal control voltage input 8 to 230V UC, electrically isolated from the 230V supply voltage and switching voltage. No minimum load required. Alternatively, PWM control with 10-24V DC at the PWM and GND connections. The setting of the brightness level is stored after switching off (Memory). In case of a power failure the switching position and the brightness level are stored. If applicable the dimmer will be switched on at the stored brightness level after the supply voltage is recovered. Automatic electronic overload protection and over-temperature switch-off. Maximum brightness (fully dimmed up) is adjustable using the upper % rotary switch. Use the middle % rotary switch to set the minimum brightness (fully dimmed down). The lower rotary switch sets the operating mode: ON: Permanent ON at maximum brightness. Pos. 1 is an AUTO position and allows the dimming of all lamp types. Switch on and off using pushbutton on the device and/or pushbutton connected to +A1/-A2. Dimming via rotary knob. Pos. 2 is a comfort setting for dimmable 230V LED lamps which cannot be dimmed down far enough on AUTO (phase cut-off) due to the design and must therefore be forced at phase control. Switch on and off using pushbutton on the device and/or pushbutton connected to +A1/-A2. Dimming via rotary knob. Pos. 3 is a comfort setting for energy saving lamps which must be switched on at a higher voltage so that they can be safely switched on cold when they are dimmed down. Switch on and off using pushbutton on the device and/or pushbutton connected to +A1/-A2. Dimming via rotary knob. Pos. 4 is an AUTO position and allows the dimming of all lamp types. Switch on and off using switch connected to +A1/-A2. Dimming via rotary knob. Pos. 5 is a comfort setting for dimmable 230V LED lamps which cannot be dimmed down far enough on AUTO (phase cut-off) due to the design and must therefore be forced at phase control. Switch on and off using switch connected to +A1/-A2. Dimming via rotary knob. Pos. 6 is a comfort setting for energy saving lamps which must be switched on at a higher voltage so that they can be safely switched on cold when they are dimmed down. Switch on and off using switch connected to +A1/-A2. Dimming via rotary knob. Pos. 7 is an AUTO position and allows the dimming of all lamp types. Switch on and off and dimming with PWM activation. Pos. 8 is a comfort setting for dimmable 230V LED lamps which cannot be dimmed down far enough on AUTO (phase cut-off) due to the design and must therefore be forced at phase control. Switch on and off and dimming with PWM activation. In positions 2, 3, 5, 6 and 8 no inductive (wound) transformers should be used. OFF: Permanent OFF. The LED under the upper rotary switch lights up when the lamp is switched on.