Wireless actuator heating/cooling relay

Prekės būklė	Nauja
Gamintojo pavadinimas	Wireless actuator heating/cooling relay
Prekės ženklas	ELTAKO
Kategorijos	Jungikliai
Kilmės šalis	CN
Suderintos sistemos kodas	8526 9200 00
Montavimo metodas	Apatinis sluoksnis (tinko)
Spalva	Mėlynas
Be halogeno	Yes
Paviršiaus apdorojimas	Kita
Srovės tiekimas	12-24 V AC/DC
Relių skaičius	1
Tinka jungikliui	No
Tinka impulsiniam mygtukui	No
Tinka tamsinimo sistemai	No
Tinka suvyniojamos uždangos jungikliui	No
Medžiagos kokybė	Termoplastikas
Medžiaga	Plastikinis
Tvirtinimo tipas	Kita
Ritininio kodo sistema	Yes
Komandų skaičius	32
Radijo dažnis	868 MHz
Korpuse	Yes
Vamzdžio bazės korpuse	No
Štampuojama grandinės plokštė / modulis	No
Paspaudimo mygtuko režimas	No
Perjungimo režimas	No
Su rankiniu radijo siųstuvu	No
Su radijo kodavimo įrenginiu	No
Su radijo bangomis valdomu paspaudžiamu mygtuku	No
Tinka su pakeliamų žaliuzių / suvyniojamos uždangos jungikliu	No
Tinka pakeliamų žaliuzių uždangos jungikliui	No
Permatomas	No
Paviršiaus tipas	Kilimėlis
Tinka apsaugos laipsniui (IP)	IP20
Galimas IFTTT palaikymas	No
Suderinamas su Apple HomeKit	No
Suderinamas su Google Assistant	No
Suderinamas su Amazon Alexa	No

Pakavimo lygis 1	4010312315118, 4010312315118
Pakavimo lygis 2	4010312315118
Pakavimo lygis 3	4010312315118

1 NO contact potential free 10A/250V AC. Only 0.8 watt standby loss. Encrypted wireless, bidirectional wireless and repeater function are switchable. For installation. 45mm long, 45mm wide, 33mm deep. Supply voltage 230V. If a power failure occurs, the switching state is retained. If a power failure occurs repeatedly, the device is switched off in a defined sequence. By using a bistable relay coil power loss and heating is avoided even in the on mode. After installation, wait for short automatic synchronisation before the switched consumer is connected to the mains. This heating/cooling relay evaluates the information from wireless temperature controllers or sensors. Possibly supplemented by window/door contacts, motion detector, window handle sensor FFG7B and wireless pushbuttons. You can teach in encrypted sensors. You can switch on bidirectional wireless and/or a repeater function. Every change in state of the contact is confirmed by a wireless telegram. This wireless telegrame an be taught-in into other actuators and Professional Smart Home controllers. Especially into a FSR61 to synchronously switch a heat circulating pump with the valves. Upper rotary switch for operating modes: H1: Heating operation with PWM control at T = 4 minutes (PWM = pulse width modulation). (suitable for valves with thermoelectric valve drive) H2: Heating operation with PWM control at T = 15 minutes. (suitable for valves with motor-driven valve drive) H3: Operating mode with 2-point control. K1: Cooling operation with PWM control at T = 15 minutes. K2: Cooling mode with 2-point control. Switchover is visualised by LEDs flashing. Lower rotary switch for adjustable hysteresis and PWM influence: Left stop: lowest hysteresis 0.5°. Middle position: hysteresis 2.5°. Right stop: largest ­hysteresis 4.5°. Inbetween, divisions in steps of 0.5° visualised by LEDs flashing. Two-point control mode: The hysteresis rotary switch sets the required difference between the switch-on and switch-off temperatures. When the actual temperature >= reference temperature, the device is switched off. When the actual temperature <= (reference temperature – hysteresis), the device is switched on. The signs are the opposite in cooling mode. PWM control mode: The hysteresis rotary switch set the required temperature difference at which the device is switched on at 100%. When the actual temperature >= reference temperature, the device is switched off. When the actual temperature <= (reference temperature – hysteresis), the device is switched on at 100%. If the actual temperature lies between the reference temperature – hysteresis and the reference temperature, the device is switched on and off with a PWM in steps of 10% depending on the temperature difference. The lower the temperature difference, the shorter the switch-on time. As a result of the settability of the 100% value, the PWM can be adapted to the heater size and inertia. The signs are the opposite in cooling mode. In heating mode, the frost protection function is always enabled. As soon as the actual temperature drops below 8°C, the temperature is controlled in the selected operating mode to 8°C. If one or several windows are open, the output remains off provided the window/door contacts FTK or window handle sensors FFG7B are taught-in. In heating mode, however, the frost protection remains enabled. As long as all taught-in motion detectors FBH detect no motion, the device is switched to setback mode. In heating mode, the reference temperature is set back by 2°. In cooling mode, it is raised by 2°. As soon as a motion detector signals movement again, the device is switched to normal mode. When a wireless pushbutton FT4 is taught-in, the assignment of the 4 keys is assigned with the following fixed functions: Top right: Normal mode (can also be enabled by timer). Bottom right: Night setback mode by 4°. In cooling mode, raised by 4° (can also be enabled by timer). Top left: Setback mode by 2°, in cooling mode, raised by 2°. Bottom left: Off (in heating mode, frost protection enabled. In cooling mode permanent off). If the motion detector and wireless pushbutton are taught-in at the same time, the last telegram received is always the one that is valid. A motion detector therefore switches off a setback mode selected by wire­less pushbutton when a movement is detected. The LED performs during the teach-in process according to the operating instructions. It shows wireless control commands by short flickering during operation.