Analogue settable multifunction time relay 1 CO contact 10A

Prekės būklė	Nauja
Gamintojo pavadinimas	Analogue settable multifunction time relay 1 CO contact 10A
Prekės ženklas	ELTAKO
Kategorijos	Relės
Kilmės šalis	CN
Suderintos sistemos kodas	8536 4900 00
Montavimo metodas	DIN bėgis
Funkcija	Daugiafunkcinis
Suprojektuotas aukštis	58 mm
Sužadinimo tipas	Analaginis su daug funkcijų
Modulinių tarpų skaičius plotyje	1
Perjungimo jungiklių skaičius	1
1 kontrolinė įtampa	8-230 V
1 kontrolinės įtampos tipas	Kintamoji ar nuolatinė srovė
1 kontrolinės įtampos dažnis	50 Hz
Tiekimo įtampos tipas	Kintamoji ar nuolatinė srovė
Maitinimo įtampos diapazonas	8-230 V
1 intervalo vienetas	Minutės/ valandos
1 intervalas nuo / iki	0.1-40
Kaitrinių lempų jungiklio pajėgumas	2000 W
Fluorescencinės DUO lempos jungiklio pajėgumas	1000 VA
Fluorescencinės indukcinės lempos jungiklio pajėgumas	1000 VA
Fluorescencinės lygiagrečios lempos jungiklio pajėgumas	500 VA
Įprastai uždarytų kontaktų skaičius	0
Įprastai atvirų kontaktų skaičius	0

Pakavimo lygis 1	4010312603086, 4010312603086
Pakavimo lygis 2	4010312603086
Pakavimo lygis 3	4010312603086

1 CO contact potential free 10A/250V AC. 230V LED lamps up to 200W, incandescent lamps 2000W*. Standby loss 0.02–0.6 watt only. Modular device for DIN-EN 60715 TH35 rail mounting. 1 module = 18mm wide, 58mm deep. With the patented Eltako Duplex technology (DX) the normally potential-free contacts can still switch in zero passage when switching 230V AC 50Hz and therefore drastically reduce wear. Simply connect the neutral conductor to the terminal (N) and L to 15(L) for this. This gives an additional standby consumption of only 0.1 Watt. Universal control voltage from 8 to 230V UC. Supply voltage same as control voltage. Time setting between 0.1 second and 40 hours. By using a bistable relay coil power loss and heating is avoided even in the on mode. The switched consumer may not be connected to the mains before the short automatic synchronisation after installation has terminated. According to the connection of the power supply to the terminals B1-A2 or B2-A2 two different levels of settings can be selected: Functions F with connection of the power supply to B1-A2 (Standby loss 0.02-0.4W): RV = off delay. AV = operate delay. TI = clock generator starting with impulse. TP = clock generator starting with pause. IA = impulse controlled operate delay (e.g. automatic door opener). EW = fleeting NO contact. AW = fleeting NC contact. ARV = operate and release delay. ON = permanent ON. OFF = permanent OFF. Functions (F) with connection of the power supply to B2-A2 (Standby loss 0.02-0.6W): SRV = release-delay impulse switch. ER = relay. EAW = fleeting NO contact and fleeting NC contact. ES = impulse switch. IF = pulse shaper. ARV+ = additive operate and release delay. ESV = impulse switch with release delay and switch-off early-warning function. AV+ = additive operate delay. ON = permanent ON. OFF = permanent OFF. The LED below the big rotary switch indicates the contact position while time-out is in progress. It blinks while the relay contact 15-18 is open (15-16 closed), and is continuously ON as long as the relay contact 15-18 is closed (15-16 open). The time base T is selected by means of the middle, latching rotary switch T. Time-base figures available are 0.1 seconds, 0.5 seconds, 2 seconds, 5 seconds, 1 minute, 2 minutes, 5 minutes, 1 hour, 2 hours and 4 hours. The total time is obtained by multiplying the timebase by the multiplier. The multiplier xT is set on the upper, latching rotary switch xT and is in the range from 1 to 10. Thus, time settings can be selected in the range from 0.1 second (time base 0.1 second and multiplier 1) and 40 hours (time base 4 hours and multiplier 10). * The maximum load can be used starting at a delay time or clock cycle of 5 minutes. The maximum load will be reduced for shorter times as follows: up to 2 seconds 15%, up to 2 minutes 30%, up to 5 minutes 60%.