Universal dimmer switch, Power MOSFET up to 400W

Toote seisukord	Uus
Bränd	ELTAKO
Kategooriad	Lülitid
Päritoluriik	CN
Harmoneeritud süsteemi kood	8536 5080 00
Kooste ehitus	Muul viisil
Talitlusviis	Puutetundlik nupp
Sagedus	50 Hz
Koormuse liik	Universaalne
Nimipinge	230 V
Laius	18 mm
Kõrgus	58 mm
Seadme sügavus	66 mm
Max. switching power LED	400 W

Pakkimistase 1	4010312107843, 4010312107843
Pakkimistase 2	4010312107843
Pakkimistase 3	4010312107843

Paigaldusviis	DRA (DIN liistule)
Värvus	Sinine
Halogeenivaba	Yes
Ühenduse liik	Kruviklemmid
Pinnatöötlus	Muul viisil
Materjal	Termoplastist
Materjal	Plast
Kinnitusviis	Haakuriga
Valgustatuse mälu	Yes
Alajaama sisend	No
Serial dimmer	No
Rakendatav koos liikumisanduriga	No
Rakendatav koos edastuslülitiga	No
Rakendatav koos infrapunalülitiga	No
Rakendatav koos olemasolu indikaatoriga	No
Rakendatav koos nupplülitiga	Yes
Rakendatav koos aeglüliti/taimeriga	No
Juhtimispinge	8-230 V
Läbipaistev	No
Pinna liik	Matt
Südamiku ristlõige	6 mm²
Saadaval on rakenduste IFTTT sobitustugi	No
Reguleerimine, faasi väljalülitamine	Yes
Reguleerimine, faasi sisselülitamine	Yes
Rakenduse juhtimine sinihambaga (Bluetooth)	No
Nominal power resistive load	400 W
Nominal power inductive load	400 VA
Nominal power capacitive load	400 VA
Compatible with Apple HomeKit	No
Compatible with Google Assistant	No
Compatible with Amazon Alexa	No

Universal dimmer switch. Power MOSFET up to 400W. Automatic lamp ­detection. Standby loss 0.1 watt only. With adjustable minimum or maximum brightness and dimming speed. With switching operation for children's rooms and snooze function. Modular device for DIN EN 60715 TH35 rail mounting. 1 module = 18mm wide, 58mm deep. Universal dimmer switch for lamps up to 400W, depending on ventilation conditions, dimmable 230V LED lamps and dimmable energy saving lamps (ESL) are also dependent on the lamp electronics and the and the dimming technology. Zero passage switching with soft start and soft OFF to protect lamps. Universal control voltage input 8 to 230V UC, electrically isolated from the 230V supply voltage and switching voltage. No minimum load required. Short-time control commands switch on/off, permanent control varies the brightness to the maximum level. An interruption of control changes the direction of dimming. The setting of the brightness level is stored after switching off. In case of a power failure the switching position and the brightness level are stored. If applicable the dimmer will be switched on at the stored brightness level after the supply voltage is recovered. Glow lamp current up to 5mA starting at 110V. Automatic electronic overload protection and over-temperature switch-off. The LED below the top rotary switch on the front shows control commands. It starts blinking after 15 seconds if a pushbutton is inhibited. The upper rotary switch determines the operation, whether the automatic lamp detection or special comfort positions should act: AUTO allows the dimming of all light species. LC1 is a comfort position for dimmable 230V LED lamps which are not being dimmed down enough when set to AUTO (trailing phase angle) dependent on the construction and must therefore be forced to leading phase angle. LC2 and LC3 are comfort positions for dimmable 230V LED lamps like LC1, but with different dimming curves. EC1 is a comfort position for energy saving lamps which must be switched on with increased power dependent on the construction, so they will also switch on again safely in cold condition when dimmed down. EC2 is a comfort position for energy saving lamps which will not be switched on again when dimmed down dependent on the construction. Memory is switched off in this position. In positions LC1, LC2, LC3, EC1 and EC2 no inductive (wound) transformers should be used. In addition, the maximum number of dimmable LED lamps can be lower than in the AUTO position dependent on the construction. The minimum brightness level (completely dimmed down) or the maximum brightness level (completely dimmed up) is adjustable with the middle %lamp rotary switch. The dimming speed can be adjusted with the lower dimming speed rotary switch. The duration of soft start and soft OFF is changed simultaneously. With special switching operation for children's rooms: If the light is switched on by holding down the pushbutton, it starts at the lowest brightness level after approx. 1 second and dims up slowly as long as the pushbutton is held down without modifying the last stored brightness level. Snooze function: With a double impulse the lighting is dimmed down from the current dimming position to the minimum brightness level and switched off. The current dimming position as well as the adjustable minimum brightness level determine the dimming time (max. = 60 minutes) which can be reduced as required. It can be switched off at any time by short-time control commands during the lighting is dimmed down. Holding down the pushbutton during the dimming down process dims up and stops the snooze function. Mixing of L loads (inductive loads, e.g. wound transformers) and C loads (capacitive loads, e.g. electronic transformers) is not permitted. R loads (ohmic loads, e.g. 230V incandescent lamps and halogen lamps) may be added anytime. Mixing of L loads and C loads is possible with the dimmer switch EUD12D in connection with capacity enhancer LUD12.