Registreeru, et avada oma eksklusiivsed B2B hinnad ja alustada ostlemist. Registreeru kohe!
1-10V control dimmer switch for electronic ballast units, 1 NO contact 600VA image 1
1-10V control dimmer switch for electronic ballast units, 1 NO contact 600VA image 2
1-10V control dimmer switch for electronic ballast units, 1 NO contact 600VA thumbnail 1
1-10V control dimmer switch for electronic ballast units, 1 NO contact 600VA thumbnail 2

1-10V control dimmer switch for electronic ballast units, 1 NO contact 600VA

Laos: Jah Hankija laovaru: Ei Minimaalne tellimuse kogus: 1
Hind (ilma KM-ta):
42,03 €
Hind kehtib kuni 31.12.24 või kuni kaupa jätkub
EAN: 4010312109496
MPN: 61100800
Pakend: 1

Technical Information

Toote seisukord Uus
Tootja nimi 1-10V control dimmer switch for electronic ballast units, 1 NO contact 600VA
Bränd ELTAKO
Kategooriad Lülitid
Päritoluriik CN
Harmoneeritud süsteemi kood 8536 5080 00
Kooste ehitus Muul viisil
Talitlusviis Puutetundlik nupp
Koormuse liik Mahtuvuslik koormus

Pakendamise üksikasjad

Pakkimistase 1 4010312109496, 4010312109496
Pakkimistase 2 4010312109496
Pakkimistase 3 4010312109496

Muud tehnilised andmed

Paigaldusviis Süvistatud paigaldus (krohvi)
Värvus Sinine
Halogeenivaba Yes
Ühenduse liik Kruviklemmid
Pinnatöötlus Muul viisil
Materjal Termoplastist
Materjal Plast
Kinnitusviis Muul viisil
Valgustatuse mälu Yes
Alajaama sisend No
Serial dimmer No
Rakendatav koos liikumisanduriga Yes
Rakendatav koos edastuslülitiga No
Rakendatav koos infrapunalülitiga No
Rakendatav koos olemasolu indikaatoriga Yes
Rakendatav koos nupplülitiga Yes
Rakendatav koos aeglüliti/taimeriga Yes
Läbipaistev No
Pinna liik Matt
Saadaval on rakenduste IFTTT sobitustugi No
Reguleerimine, faasi väljalülitamine No
Reguleerimine, faasi sisselülitamine No
Rakenduse juhtimine sinihambaga (Bluetooth) No
Compatible with Apple HomeKit No
Compatible with Google Assistant No
Compatible with Amazon Alexa No

Allalaadimised

Kirjeldus

1 NO contact not potential free 600VA and 1-10V control output 40mA. Only 1 watt standby loss. With adjustable dimming speed. With switching operation for children's rooms and snooze function. With pushbutton or switch activation. Built-in device for installation. 45mm long, 45mm wide, 33mm deep. Zero passage switching with soft ON and soft OFF to protect lamps. Also adapted for LED driver with 1-10V passive interface, without voltage source up to 0.6mA, above this value an additional voltage source is necessary. Switching voltage and control voltage 230V. State-of-the-art hybrid technology combines advantages of nonwearing electronic control with high capacity of special relays. The load is switched on and off by a bistable relay at output EVG (electronic ballast units). Switching capacity for fluorescent lamps or LV halogen lamps with electronic ballast units 600VA. By using a bistable relay coil power loss and heating is avoided even in the on mode. After installation, wait for short automatic synchronisation before the switched consumer is ­connected to the mains. Short-time control commands switch on/off, permanent control varies the brightness up to the maximum level. An interruption of control changes the direction of dimming. The brightness level is stored after switching off. In case of a power failure the switching position and the brightness level are stored. If applicable the dimmer will be switched on at the stored brightness level after the supply voltage is recovered. The dimming speed is adjustable using the dimming speed rotary switch (only for pushbutton activation). If light switches cannot be replaced by light pushbuttons, the rotary switch can be set to the switch symbol at the right stop: When the closed switch is briefly opened, the light is dimmed until the switch is briefly opened again. The dimming direction is changed automatically at each of the two vertices. In addition the direction can be changed by opening the switch briefly twice. Switching operation for children's rooms (only for pushbutton activation): If the light is switched on by holding down the pushbutton, it starts at the lowest brightness level after approx. 1 second and dims up slowly as long as the pushbutton is held down without modifying the last stored brightness level. Snooze function (only for pushbutton activation): With a double impulse the lighting is dimmed down from the current dimming position to the minimum brightness level and switched off. The current dimming position as well as the adjustable minimum brightness level determine the dimming time (max. = 60 minutes) which can be reduced as required. It can be switched off at any time by short-time control commands during the lighting is dimmed down. Holding down the pushbutton during the dimming down process dims up and stops the snooze function.