1 channel DALI LED dimmer 16A for ceiling installation

Toote seisukord	Uus
Tootja nimi	1 channel DALI LED dimmer 16A for ceiling installation
Bränd	ELTAKO
Kategooriad	Lülitid
Päritoluriik	BG
Harmoneeritud süsteemi kood	8542 3190 00
Kooste ehitus	Põhielement
Talitlusviis	Surunupp
Nimipinge	12-48 V
Sobib vastava kaitseastme (IP) korral	IP20
Laius	30 mm
Kõrgus	120 mm
Seadme sügavus	22 mm
Max. switching power LED	768 W

Pakkimistase 1

4010312321522, 4010312321522

Paigaldusviis	Muul viisil
Värvus	Hall
Halogeenivaba	Yes
Ühenduse liik	Pistikuklamber
Pinnatöötlus	Töötlemata
Materjal	Termoplastist
Materjal	Plast
Kinnitusviis	Muul viisil
Valgustatuse mälu	Yes
Alajaama sisend	No
Serial dimmer	No
Rakendatav koos liikumisanduriga	No
Rakendatav koos edastuslülitiga	No
Rakendatav koos infrapunalülitiga	No
Rakendatav koos olemasolu indikaatoriga	No
Rakendatav koos nupplülitiga	Yes
Rakendatav koos aeglüliti/taimeriga	No
Juhtimispinge	9.5-22.5 V
Läbipaistev	No
Pinna liik	Matt
Südamiku ristlõige	1.5-2.5 mm²
Saadaval on rakenduste IFTTT sobitustugi	No
Reguleerimine, faasi väljalülitamine	No
Reguleerimine, faasi sisselülitamine	No
Sisseehitatud paigalduskarbi vähim sügavus	22 mm
Rakenduse juhtimine sinihambaga (Bluetooth)	No
Nominal power resistive load	768 W
Compatible with Apple HomeKit	No
Compatible with Google Assistant	No
Compatible with Amazon Alexa	No

1 channel DALI LED dimmer for ceiling installation. 120x30x22mm. Protection class IP20. Only 0.12 watt standby loss. Designed to control constant voltage LED modules (CV) at operating voltages of 12V to 48V, Sw&Dim or SwitchDim2: Operating via 1 or 2 pushbutton inputs permits brightness control without DALI. Alternatively, corridor function for direct activation with a motion detector. Dimming range 0.1%-100%. Selectable PWM frequency (122Hz/244Hz/488Hz/976Hz). Supply voltage 12V to 48V DC.·Max. connected current 16A. High efficiency. Configuration via DALI Cockpit PC software and DALI USB interface. Operating modes: The output channel is controlled by a DALI address (Device Type 6). Alternatively, it can also be operated by one (Sw&Dim) or two pushbutton inputs (SwitchDim2). SwD1, Sw&Dim: brightness. Press pushbutton briefly: On/Off. Press pushbutton long: Dim. SwD2: Scene switch (press pushbutton briefly). If you press the SwD1 input for 2 minutes, the mode changes to Corridor function. This operating mode remains enabled until the device is disconnected from the power supply (after PowerUp: operation via SwD1/SwD2). Corridor function: Mode with integrated staircase time switch (e.g. simple activation of one or several motion detectors by relay contact). When you press the input, the maximum value is switched on. After the input signal decays, the brightness remains at this value for the duration of the hold time before it drops down to the intermediate value. After the hold time for the intermediate value expires, brightness returns to the basic value. The process starts from the beginning when the input is re-activated. The DALI Cockpit software can configure 1-channel LED dimmers. You can define both group assignment and configure scene values and DALI parameters (the parameters displayed are the as-delivered states). As-delivered state: Before the first address is assigned, you can control the device using the group address G0. This preset group assignment is deleted when addresses are assigned. Afterwards, you can define any group assignment in the DALI Cockpit. The values defined in the DALI standard are generated by sending a DALI reset command.