Registreeru, et avada oma eksklusiivsed B2B hinnad ja alustada ostlemist. Registreeru kohe!
Impulse switch with tungsten pre-contact, 1 NO contact 16A
Laos: Ei
Hankija laovaru: Ei
Minimaalne tellimuse kogus: 1
Hind (ilma KM-ta):
46,85 €
EAN: 4010312206744
MPN: 21100801
Pakend: 1
Technical Information
| Toote seisukord | Uus |
| Tootja nimi | Impulse switch with tungsten pre-contact, 1 NO contact 16A |
| Bränd | ELTAKO |
| Kategooriad |
Releed |
| Päritoluriik | CN |
| Harmoneeritud süsteemi kood | 8536 4900 00 |
| Paigaldusviis | DIN liist |
| Funktsioon | Elektrooniline lüliti |
| Sisseehitussügavus | 58 mm |
| Laius mooduli arvudes | 1 |
| Juhtpinge 1 | 8-230 V |
| Juhtpinge 2 | 230 V |
| Juhtpinge 1 liik | AC/DC |
| Juhtpinge 2 liik | AC |
| Juhtpinge 1 sagedus | 50 Hz |
| Juhtpinge 2 sagedus | 50 Hz |
| Käsitööriist | No |
| Suurim lülitusvool (cos phi = 0.6) | 4 A |
| Suurim hõõglampide koormus | 3300 W |
| Suurim luminofoorlampide koormus | 1000 VA |
| Suurim luminofoorlampide koormus (kaks ahelat) | 1000 VA |
| Suurim luminofoorlampide koormus (rööpkompensatsiooniga) | 500 VA |
| Tunnuslülitusvool | 16 A |
| Normaalselt suletud kontaktide arv | 0 |
| Normaalselt avatud kontaktide arv | 1 |
| Ümberlülituskontaktide arv | 0 |
Pakendamise üksikasjad
| Pakkimistase 1 | 4010312206744, 4010312206744 |
| Pakkimistase 2 | 4010312206744 |
| Pakkimistase 3 | 4010312206744 |
Allalaadimised
Kirjeldus
1 NO contact potential free 16A/250V AC with tungsten pre-contact. 230V LED lamps up to 600W, incandescent lamp load up to 3300W. Max. inrush current 500A/2ms. No standby loss. Modular device for DIN-EN 60715 TH35 rail mounting. 1 module = 18mm wide, 58mm deep. State-of-the-art hybrid technology combines advantages of nonwearing electronic control with high capacity of special relays. With the patented Eltako Duplex technology (DX) the normally potential-free contacts can still switch in zero passage when switching 230V AC 50Hz and therefore drastically reduce wear. Simply connect the neutral conductor to the terminal (N) and L to 1(L) for this. This gives a standby consumption of only 0.1 Watt. Universal control voltage 8 to 230V UC. Low switching noise. No permanent power supply necessary, therefore no standby loss. By using a bistable relay coil power loss and heating are avoided even in the on mode. The relay contact can be open or closed during start-up. It is synchronised at first operation. The electronics does not have an internal power supply and therefore no power is consumed in any contact position. A control current flows only during a short control impulse of 0.2 seconds. This activates the microcontroller, reads the last switching state from the non-voltage memory, switches the bistable relay to its opposite state accordingly and rewrites the new switching state to memory.