Universal dimmer switch, Power MOSFET up to 800W

Toote seisukord	Uus
Bränd	ELTAKO
Kategooriad	Lülitid
Päritoluriik	CN
Harmoneeritud süsteemi kood	8536 5080 00
Kooste ehitus	Muul viisil
Talitlusviis	Puutetundlik nupp
Sagedus	50 Hz
Koormuse liik	Universaalne
Nimipinge	230 V
Laius	36 mm
Kõrgus	58 mm
Seadme sügavus	66 mm
Max. switching power LED	800 W

Pakkimistase 1	4010312109656, 4010312109656
Pakkimistase 2	4010312109656

Paigaldusviis	DRA (DIN liistule)
Värvus	Sinine
Halogeenivaba	Yes
Ühenduse liik	Kruviklemmid
Pinnatöötlus	Muul viisil
Materjal	Termoplastist
Materjal	Plast
Kinnitusviis	Haakuriga
Valgustatuse mälu	Yes
Alajaama sisend	No
Serial dimmer	No
Rakendatav koos liikumisanduriga	No
Rakendatav koos edastuslülitiga	No
Rakendatav koos infrapunalülitiga	No
Rakendatav koos olemasolu indikaatoriga	No
Rakendatav koos nupplülitiga	Yes
Rakendatav koos aeglüliti/taimeriga	No
Juhtimispinge	8-230 V
Läbipaistev	No
Pinna liik	Matt
Südamiku ristlõige	6 mm²
Saadaval on rakenduste IFTTT sobitustugi	No
Reguleerimine, faasi väljalülitamine	Yes
Reguleerimine, faasi sisselülitamine	Yes
Rakenduse juhtimine sinihambaga (Bluetooth)	No
Nominal power resistive load	800 W
Nominal power inductive load	800 VA
Nominal power capacitive load	800 VA
Compatible with Apple HomeKit	No
Compatible with Google Assistant	No
Compatible with Amazon Alexa	No

Universal dimmer switch with rotary knob, Power MOSFET up to 800W. Automatic lamp ­detection. Standby loss 0.2 watt only. With adjustable minimum and maximum brightness. Modular device for DIN EN 60715 TH35 rail mounting. 2 modules = 36mm wide, 58mm deep. Universal dimmer switch for lamps up to 800W, depending on ventilation conditions, dimmable 230V LED lamps and dimmable energy saving lamps (ESL) are also dependent on the lamp electronics and the dimming technology. Up to 3600W with capacity enhancers LUD12 at the terminals X1 and X2. Zero passage switching with soft start and soft OFF to protect lamps. Universal control voltage input 8 to 230V UC, electrically isolated from the 230V supply voltage and switching voltage. No minimum load required. Alternatively, PWM control with 10-24V DC at the PWM and GND connections. The setting of the brightness level is stored after switching off (Memory). In case of a power failure the switching position and the brightness level are stored. If applicable the dimmer will be switched on at the stored brightness level after the supply voltage is recovered. Automatic electronic overload protection and over-temperature switch-off. Maximum brightness (fully dimmed up) is adjustable using the upper % rotary switch. Use the middle % rotary switch to set the minimum brightness (fully dimmed down). The lower rotary switch sets the operating mode: ON: Permanent ON at maximum brightness. Pos. 1 is an AUTO position and allows the dimming of all lamp types. Switch on and off using pushbutton on the device and/or pushbutton connected to +A1/-A2. Dimming via rotary knob. Pos. 2 is a comfort setting for dimmable 230V LED lamps which cannot be dimmed down far enough on AUTO (phase cut-off) due to the design and must therefore be forced at phase control. Switch on and off using pushbutton on the device and/or pushbutton connected to +A1/-A2. Dimming via rotary knob. Pos. 3 is a comfort setting for energy saving lamps which must be switched on at a higher voltage so that they can be safely switched on cold when they are dimmed down. Switch on and off using pushbutton on the device and/or pushbutton connected to +A1/-A2. Dimming via rotary knob. Pos. 4 is an AUTO position and allows the dimming of all lamp types. Switch on and off using switch connected to +A1/-A2. Dimming via rotary knob. Pos. 5 is a comfort setting for dimmable 230V LED lamps which cannot be dimmed down far enough on AUTO (phase cut-off) due to the design and must therefore be forced at phase control. Switch on and off using switch connected to +A1/-A2. Dimming via rotary knob. Pos. 6 is a comfort setting for energy saving lamps which must be switched on at a higher voltage so that they can be safely switched on cold when they are dimmed down. Switch on and off using switch connected to +A1/-A2. Dimming via rotary knob. Pos. 7 is an AUTO position and allows the dimming of all lamp types. Switch on and off and dimming with PWM activation. Pos. 8 is a comfort setting for dimmable 230V LED lamps which cannot be dimmed down far enough on AUTO (phase cut-off) due to the design and must therefore be forced at phase control. Switch on and off and dimming with PWM activation. In positions 2, 3, 5, 6 and 8 no inductive (wound) transformers should be used. OFF: Permanent OFF. The LED under the upper rotary switch lights up when the lamp is switched on.