Registreeru, et avada oma eksklusiivsed B2B hinnad ja alustada ostlemist. Registreeru kohe!
Wireless actuator multifunction time relay image 1

Wireless actuator multifunction time relay

Laos: Ei Hankija laovaru: Ei Minimaalne tellimuse kogus: 1
Hind (ilma KM-ta):
72,97 €
Hind kehtib kuni 31.12.24
EAN: 4010312302293
MPN: 30100230
Pakend: 1

Technical Information

Toote seisukord Uus
Tootja nimi Wireless actuator multifunction time relay
Bränd ELTAKO
Kategooriad Lülitid
Päritoluriik CN
Harmoneeritud süsteemi kood 8526 9200 00
Paigaldusviis Süvistatud paigaldus (krohvi)
Värvus Sinine
Halogeenivaba Yes
Pinnatöötlus Muul viisil
Toide 230 V AC
Releede arv 1
Sobib lülitamiseks Yes
Sobib impulsslülitiks Yes
Sobib hämardamiseks No
Sobib rullsulguri lülitiks No
Materjal Termoplastist
Materjal Plast
Kinnitusviis Muul viisil
Muutuva koodisüsteemiga Yes
Käskude arv 32
Raadiosagedus 868 MHz
Kestas Yes
Torukujulises keres No
Trükiplaat/moodul No
Nupplülitusmoodus Yes
Lülitusmoodus Yes
Käsiraadiosaatja No
Raadiosignaali kodeerimisseade No
Raadiosignaaliga juhitava nupplülitiga No
Sobib ribikardinate lülitiks No
Sobib ribikardinate sulgemiseks No
Läbipaistev No
Pinna liik Matt
Sobib vastava kaitseastme (IP) korral IP20
Saadaval on rakenduste IFTTT sobitustugi No
Compatible with Apple HomeKit No
Compatible with Google Assistant No
Compatible with Amazon Alexa No

Pakendamise üksikasjad

Pakkimistase 1 4010312302293, 4010312302293
Pakkimistase 2 4010312302293
Pakkimistase 3 4010312302293

Allalaadimised

Kirjeldus

1 NO contact potential free 10A/250V AC, 230V LED lamps up to 400W, incandescent lamps up to 2000 watts.* Encrypted wireless, bidirectional wireless and repeater ­function are switchable. Only 0.8 watt standby loss. For installation. 45mm long, 45mm wide, 33mm deep. Supply voltage and if necessary control voltage locally 230V. If a power failure occurs, the switching state is retained. If a power failure occurs repeatedly, the device is switched off in a defined sequence. This wireless actuator features state-of-the-art hybrid technology that we developed: we combined the wear-free receiver and evaluation electronics with a bistable relay. By using a bistable relay coil power loss and heating is avoided even in the on mode. After installation, wait for short automatic synchronisation before the switched consumer is connected to the mains. In addition to the wireless control input via an internal antenna, this wireless actuator can also be controlled locally by a conventional control switch if fitted previously. Glow lamp current is not permitted. You can teach in encrypted sensors. You can switch on bidirectional wireless and/or a repeater function. Every change in state and incoming central command telegrams are confirmed by a wireless telegram. This wireless telegram can be taught-in in other actuators, Professional Smart Home controllers and in universal displays. With the top rotary switch in the setting LRN up to 35 wireless pushbuttons can be ­assigned, of which one or more central control pushbuttons. In addition, wireless window/door contacts (FTK) may have a NO or NC function when the window is open. If a direction pushbutton is taught-in, a function (e.g. TI) can be started using the top key (START) and stopped with the bottom key (STOP). The required function can then be selected. Switching will be visualised by flashing of the LED. RV = off delay. AV = operating delay. TI = clock generator starting with impulse. IA = impulse-controlled operating delay. EW = fleeting NO contact. The bottom rotary switch sets the time from 0.5 seconds to 60 minutes. The LED performs during the teach-in process according to the operating instructions. It shows wireless control commands by short flickering during operation. * The maximum load can be used from a delay time or clock cycle of 5 minutes. The maximum load is reduced for shorter times as follows: up to 2 minutes 30%, up to 5 minutes 60%.