Registreeru, et avada oma eksklusiivsed B2B hinnad ja alustada ostlemist. Registreeru kohe!
Coupling relay, 1 NO contact 16A image 1
ELTAKO

Coupling relay, 1 NO contact 16A

Laos: Ei Hankija laovaru: Ei Minimaalne tellimuse kogus: 1
Hind (ilma KM-ta):
45,05 €
Hind kehtib kuni 31.12.24
EAN: 4010312206683
MPN: 22100800
Pakend: 1

Technical Information

Toote seisukord Uus
Tootja nimi Coupling relay, 1 NO contact 16A
Bränd ELTAKO
Kategooriad Releed
Päritoluriik CN
Harmoneeritud süsteemi kood 8536 4900 00
Paigaldusviis DIN liist
Funktsioon Osaliselt elektrooniline
Sisseehitussügavus 58 mm
Tunnusvool 16 A
Laius mooduli arvudes 1
Juhtpinge 1 8-230 V
Juhtpinge 1 liik AC/DC
Juhtpinge 1 sagedus 50 Hz
Suurim lülitusvool (cos phi = 0.6) 4 A
Suurim hõõglampide koormus 2000 W
Suurim luminofoorlampide koormus 1000 VA
Suurim luminofoorlampide koormus (kaks ahelat) 1000 VA
Suurim luminofoorlampide koormus (rööpkompensatsiooniga) 500 VA
Normaalselt suletud kontaktide arv 0
Normaalselt avatud kontaktide arv 1
Ümberlülituskontaktide arv 0

Pakendamise üksikasjad

Pakkimistase 1 4010312206683, 4010312206683
Pakkimistase 2 4010312206683
Pakkimistase 3 4010312206683

Allalaadimised

Toote lehe süvalink

Kirjeldus

1 NO contact potential free 16A/250V AC with tungsten pre-contact, max. inrush current 500A/2ms. 230V LED lamps up to 600W, incandescent lamp load 3300W. No standby loss. Modular device for DIN-EN 60715 TH35 rail mounting. 1 module = 18mm wide, 58mm deep. State-of-the-art hybrid technology combines advantages of nonwearing electronic control with high capacity of special relays. With the patented Eltako Duplex technology (DX) the normally potential-free contacts can still switch in zero passage when switching 230V AC 50Hz and therefore drastically reduce wear. Simply connect the neutral conductor to the terminal (N) and L to 1(L) for this. This gives an standby consumption of only 0.1 watt. If the contact is used for controlling switching devices which do not perform zero passage switching themselves, (N) should not be connected because the additional closing delay otherwise causes the opposite effect. Universal control voltage 8 to 230 V UC. Low switching noise. Contact position indicator with LED. By using a bistable relay coil power loss and heating is avoided even in the on mode. The relay contact can be open or closed when putting into operation. It will be synchronised at first operation. This relay is not suitable to feed back the switching voltage signal of a dimmer switch. Use only relays ESR12DDX-UC, ESR12NP-230V+UC or ESR61NP-230V+UC for this purpose. The electronics does not have an internal power supply and therefore no standby loss. The microcontroller is activated when the control contact closes. This switches the bistable relay to the correct direction. The bistable relay switches back either when the control contact opens or when the control voltage falls.