Analogue settable multifunction time relay, 1 NO contact 10A

Laohinnas (käibemaksuta):

41,33 €

Hind kehtib kuni 2024-12-31

Hind m kohta: 41,33 €

EAN: 4010312603147

MPN: 23100530

Meie ladu: Ei Hankija laovaru: Ei

Pakendi kohta: 1 Kasti kohta: 1 Kaubaaluse kohta: N/A

Tehnilised andmed

Toote seisukord	Uus
Tootja nimi	Analogue settable multifunction time relay, 1 NO contact 10A
Bränd	ELTAKO
Kategooriad	Releed
Päritoluriik	CN
Harmoneeritud süsteemi kood	8536 5080 00
Paigaldusviis	DIN liist
Funktsioon	Mitmeotstarbeline
Kõrgus	58 mm
Aktiveerimismoodus	Analoog, multifunktsionaalne
Laius mooduli arvudes	1
Ümberlülitite arv	0
Juhtpinge 1	230 V
Juhtpinge 1 liik	AC
Juhtpinge 1 sagedus	50 Hz
Toitepinge liik	AC
Toitepinge	230 V
1. intervalliüksus	Minutit/tundi
1. intervall	0.1-40
Nimilülitusvool pingel 250 V AC	10 A
Hõõglampide lülitusvõime	1000 W
Luminofoorlampide lülitusvõime DUO	500 VA
Luminofoorlampide lülitusvõime, induktiivkoormus	500 VA
Luminofoorlamide lülitusvõime, rööpühenduses	250 VA
Normaalselt suletud kontaktide arv	0
Normaalselt avatud kontaktide arv	1

Pakendamise üksikasjad

Pakkimistase 1	4010312603147, 4010312603147
Pakkimistase 2	4010312603147
Pakkimistase 3	4010312603147

Downloads

Toote lehe süvalink

Kirjeldus

1 NO contact potential free 10A/250V AC. 230V LED lamps up to 200W, incandescent lamps 1000W*. Standby loss 0.4 watt only. Modular device for DIN-EN 60715 TH35 rail mounting. 1 module = 18mm wide, 58mm deep. Control voltage 230V. Supply voltage same as control voltage. Time setting between 0.1 second and 40 hours. Functions F: RV = off delay. AV = operate delay. TI = clock generator starting with impulse. TP = clock generator starting with pause. IA = impulse controlled operate delay (e.g. automatic door opener). EW = fleeting NO contact. AW = fleeting NC contact. ARV = operate and release delay. ON = permanent ON. OFF = permanent OFF. The LED below the big rotary switch indicates the contact position while time-out is in progress. It blinks while the relay contact is open, and is continuously ON as long as the relay contact is closed. The time base T is selected by means of the middle, latching rotary switch T. Time-base figures available are 0.1 seconds, 0.5 seconds, 2 seconds, 5 seconds, 1 minute, 2 minutes, 5 minutes, 1 hour, 2 hours and 4 hours. The total time is obtained by multiplying the timebase by the multiplier. The multiplier xT is set on the upper, latching rotary switch xT and is in the range from 1 to 10. Thus, time settings can be selected in the range from 0.1 second (time base 0.1 second and multiplier 1) and 40 hours (time base 4 hours and multiplier 10). * The maximum load can be used starting at a delay time or clock cycle of 5 minutes. The maximum load will be reduced for shorter times as follows: up to 2 seconds 15%, up to 2 minutes 30%, up to 5 minutes 60%.