1-10V control dimmer switch for electronic ballast units, 1 NO contact 600VA

Preces stāvoklis	Jauns
Zīmols	ELTAKO
Kategorijas	Gaismas slēdži
Izcelsmes valsts	CN
Harmonizētās sistēmas kods	8536 5080 00
Montāžas izkārtojums	Citi
Darbības metode	Skārienkontroles poga
Slodzes veids	Kapacitatīvā slodze

Iepakojuma līmenis 1	4010312109496, 4010312109496
Iepakojuma līmenis 2	4010312109496
Iepakojuma līmenis 3	4010312109496

Montāžas metode	Iebūvējams vienā līmenī (apmetums)
Krāsa	Zils
Nesatur halogēnus	Yes
Savienojuma veids	Skrūvējams termināls
Virsmas aizsardzība	Citi
Materiāla kvalitāte	Termoplasts
Materiāls	Plastmasas
Stiprinājuma veids	Citi
Gaismas vērtību atmiņa	Yes
Apakšstacijas ieeja	No
Sērijveida dimmer	No
Piemērojams ar kustību sensoru	Yes
Piemērojams ar pārraides pogu	No
Piemērojams ar infrasarkano pogu	No
Piemērojams ar klātbūtnes indikatoru	Yes
Piemērojams ar pogu	Yes
Piemērojams ar laika slēdzi/taimeri	Yes
Caurspīdīgs	No
Virsmas apdare	Matt
Ir pieejams IFTTT atbalsts	No
Aptumšošanas fāzes atslēgšana	No
Aptumšošanas fāzes pārslēgšana	No
Lietotņu vadība, izmantojot Bluetooth	No
Savietojams ar Apple HomeKit	No
Savietojams ar Google palīgu	No
Savietojams ar Amazon Alexa	No

1 NO contact not potential free 600VA and 1-10V control output 40mA. Only 1 watt standby loss. With adjustable dimming speed. With switching operation for children's rooms and snooze function. With pushbutton or switch activation. Built-in device for installation. 45mm long, 45mm wide, 33mm deep. Zero passage switching with soft ON and soft OFF to protect lamps. Also adapted for LED driver with 1-10V passive interface, without voltage source up to 0.6mA, above this value an additional voltage source is necessary. Switching voltage and control voltage 230V. State-of-the-art hybrid technology combines advantages of nonwearing electronic control with high capacity of special relays. The load is switched on and off by a bistable relay at output EVG (electronic ballast units). Switching capacity for fluorescent lamps or LV halogen lamps with electronic ballast units 600VA. By using a bistable relay coil power loss and heating is avoided even in the on mode. After installation, wait for short automatic synchronisation before the switched consumer is ­connected to the mains. Short-time control commands switch on/off, permanent control varies the brightness up to the maximum level. An interruption of control changes the direction of dimming. The brightness level is stored after switching off. In case of a power failure the switching position and the brightness level are stored. If applicable the dimmer will be switched on at the stored brightness level after the supply voltage is recovered. The dimming speed is adjustable using the dimming speed rotary switch (only for pushbutton activation). If light switches cannot be replaced by light pushbuttons, the rotary switch can be set to the switch symbol at the right stop: When the closed switch is briefly opened, the light is dimmed until the switch is briefly opened again. The dimming direction is changed automatically at each of the two vertices. In addition the direction can be changed by opening the switch briefly twice. Switching operation for children's rooms (only for pushbutton activation): If the light is switched on by holding down the pushbutton, it starts at the lowest brightness level after approx. 1 second and dims up slowly as long as the pushbutton is held down without modifying the last stored brightness level. Snooze function (only for pushbutton activation): With a double impulse the lighting is dimmed down from the current dimming position to the minimum brightness level and switched off. The current dimming position as well as the adjustable minimum brightness level determine the dimming time (max. = 60 minutes) which can be reduced as required. It can be switched off at any time by short-time control commands during the lighting is dimmed down. Holding down the pushbutton during the dimming down process dims up and stops the snooze function.