Reģistrējieties, lai atbloķētu savas ekskluzīvās B2B cenas un sāktu iepirkties. Reģistrējieties tagad!
Impulse switch, 1 NO contact + 1 NC contact 16A
Ir noliktavā: Nē
Piegādātāja krājumi: Nē
Minimālais pasūtījuma daudzums: 1
Cena (bez PVN):
36,54 €
EAN: 4010312108055
MPN: 21110002
Iepakojums: 1
Technical Information
| Preces stāvoklis | Jauns |
| Ražotāja nosaukums | Impulse switch, 1 NO contact + 1 NC contact 16A |
| Zīmols | ELTAKO |
| Kategorijas |
Releji |
| Izcelsmes valsts | CN |
| Harmonizētās sistēmas kods | 8536 5080 00 |
| Montāžas metode | DIN sliede |
| Funkcija | Elektroniskais slēdzis |
| Iebūvēts dziļums | 58 mm |
| Platums moduļu atstarpju skaitā | 1 |
| Vadības spriegums 1 | 8-230 V |
| Vadības spriegums 2 | 230 V |
| Vadības sprieguma veids 1 | AC/DC |
| Vadības sprieguma veids 2 | AC |
| Frekvences vadības spriegums 1 | 50 Hz |
| Frekvences vadības spriegums 2 | 50 Hz |
| Piemērots manuālai darbībai | No |
| Maks. pārslēgšanas strāva (cos phi = 0,6) | 4 A |
| Maks. kvēlspuldžu slodze | 2000 W |
| Maks. slodzes dienasgaismas spuldze | 1000 VA |
| Maks. slodzes dienasgaismas spuldze (Duo ķēde) | 1000 VA |
| Maks. slodzes dienasgaismas spuldze (paralēli kompensēta) | 500 VA |
| Nominālā slēdža strāva | 16 A |
| Kontaktu skaits kā parasti slēgtam kontaktam | 1 |
| Kontaktu skaits kā parasti atvērtam kontaktam | 1 |
| Kontaktpersonu skaits kā maiņas kontaktpersona | 0 |
Iepakojuma informācija
| Iepakojuma līmenis 1 | 4010312108055, 4010312108055 |
| Iepakojuma līmenis 2 | 4010312108055 |
| Iepakojuma līmenis 3 | 4010312108055 |
Lejupielādes
Apraksts
1 NO contact + 1 NC contact potential free 16A/250V AC. 230V LED lamps up to 200W, incandescent lamp load up to 2000W. No standby loss. Modular device for DIN-EN 60715 TH35 rail mounting. 1 module = 18mm wide, 58mm deep. Either universal control voltage 8 to 230V UC at the control input +A1/A2 or 230V with glow lamp current up to 5mA at the control input (L)/-A2(N). The simultaneous use of two potentials at the control inputs is not permitted. Very low switching noise. No permanent power supply necessary, therefore no standby loss. State-of-the-art hybrid technology combines advantages of nonwearing electronic control with high capacity of special relays. By using a bistable relay coil power loss and heating is avoided even in the on mode. The relay contact can be open or closed when putting into operation. It will be synchronised at first operation. Same terminal connection as the electromechanical impulse switch S12-110-. If this impulse switch is in a circuit, which is monitored by a FR12-230V mains disconnection relay, no additional base load is required. However, the monitoring voltage of the FR12-230V must be set to max. The electronics does not have an internal power supply and therefore no power is consumed in any contact position. A control current flows only during a short control impulse of 0.2 seconds. This activates the microcontroller, reads the last switching state from the non-voltage memory, switches the bistable relay to its opposite state accordingly and rewrites the new switching state to memory.