Impulse switch with tungsten pre-contact, 1 NO contact 16A
Noliktavas cena (bez PVN):
46,85 €
Šī cena ir spēkā līdz 2024-12-31
Cena par m:
46,85 €
EAN: 4010312206744
MPN: 21100801
Mūsu noliktava:
Nē
Piegādātāja krājumi:
Nē
Vienā iepakojumā:
1
Vienā kastē:
1
Vienā paletē:
N/A
Tehniskie dati
| Preces stāvoklis | Jauns |
| Zīmols | ELTAKO |
| Kategorijas |
Releji |
| Izcelsmes valsts | CN |
| Harmonizētās sistēmas kods | 8536 4900 00 |
| Montāžas metode | DIN sliede |
| Funkcija | Elektroniskais slēdzis |
| Iebūvēts dziļums | 58 mm |
| Platums moduļu atstarpju skaitā | 1 |
| Vadības spriegums 1 | 8-230 V |
| Vadības spriegums 2 | 230 V |
| Vadības sprieguma veids 1 | AC/DC |
| Vadības sprieguma veids 2 | AC |
| Frekvences vadības spriegums 1 | 50 Hz |
| Frekvences vadības spriegums 2 | 50 Hz |
| Piemērots manuālai darbībai | No |
| Maks. pārslēgšanas strāva (cos phi = 0,6) | 4 A |
| Maks. kvēlspuldžu slodze | 3300 W |
| Maks. slodzes dienasgaismas spuldze | 1000 VA |
| Maks. slodzes dienasgaismas spuldze (Duo ķēde) | 1000 VA |
| Maks. slodzes dienasgaismas spuldze (paralēli kompensēta) | 500 VA |
| Nominālā slēdža strāva | 16 A |
| Kontaktu skaits kā parasti slēgtam kontaktam | 0 |
| Kontaktu skaits kā parasti atvērtam kontaktam | 1 |
| Kontaktpersonu skaits kā maiņas kontaktpersona | 0 |
Iepakojuma informācija
| Iepakojuma līmenis 1 | 4010312206744, 4010312206744 |
| Iepakojuma līmenis 2 | 4010312206744 |
| Iepakojuma līmenis 3 | 4010312206744 |
Downloads
Apraksts
1 NO contact potential free 16A/250V AC with tungsten pre-contact. 230V LED lamps up to 600W, incandescent lamp load up to 3300W. Max. inrush current 500A/2ms. No standby loss. Modular device for DIN-EN 60715 TH35 rail mounting. 1 module = 18mm wide, 58mm deep. State-of-the-art hybrid technology combines advantages of nonwearing electronic control with high capacity of special relays. With the patented Eltako Duplex technology (DX) the normally potential-free contacts can still switch in zero passage when switching 230V AC 50Hz and therefore drastically reduce wear. Simply connect the neutral conductor to the terminal (N) and L to 1(L) for this. This gives a standby consumption of only 0.1 Watt. Universal control voltage 8 to 230V UC. Low switching noise. No permanent power supply necessary, therefore no standby loss. By using a bistable relay coil power loss and heating are avoided even in the on mode. The relay contact can be open or closed during start-up. It is synchronised at first operation. The electronics does not have an internal power supply and therefore no power is consumed in any contact position. A control current flows only during a short control impulse of 0.2 seconds. This activates the microcontroller, reads the last switching state from the non-voltage memory, switches the bistable relay to its opposite state accordingly and rewrites the new switching state to memory.