Universal dimmer switch, Power MOSFET up to 400W

Preces stāvoklis	Jauns
Ražotāja nosaukums	Universal dimmer switch, Power MOSFET up to 400W
Zīmols	ELTAKO
Kategorijas	Gaismas slēdži
Izcelsmes valsts	CN
Harmonizētās sistēmas kods	8536 5080 00
Montāžas izkārtojums	Citi
Darbības metode	Skārienkontroles poga
Slodzes veids	Universālā
Nominālais spriegums	230 V
Ierīces platums	45 mm
Ierīces augstums	45 mm
Ierīces dziļums	18 mm

Iepakojuma līmenis 1	4010312108062, 4010312108062
Iepakojuma līmenis 2	4010312108062
Iepakojuma līmenis 3	4010312108062

Montāžas metode	Iebūvējams vienā līmenī (apmetums)
Krāsa	Zils
Nesatur halogēnus	Yes
Savienojuma veids	Skrūvējams termināls
Virsmas aizsardzība	Neapstrādāts
Materiāla kvalitāte	Termoplasts
Materiāls	Plastmasas
Stiprinājuma veids	Montāža ar skrūvi
Gaismas vērtību atmiņa	Yes
Apakšstacijas ieeja	No
Sērijveida dimmer	No
Piemērojams ar kustību sensoru	No
Piemērojams ar pārraides pogu	No
Piemērojams ar infrasarkano pogu	No
Piemērojams ar klātbūtnes indikatoru	No
Piemērojams ar pogu	Yes
Piemērojams ar laika slēdzi/taimeri	No
Vadības spriegums	230 V
Caurspīdīgs	No
Virsmas apdare	Matt
Serdes šķērsgriezums	4 mm²
Ir pieejams IFTTT atbalsts	No
Aptumšošanas fāzes atslēgšana	No
Aptumšošanas fāzes pārslēgšana	No
Min. iebūvētās instalācijas kastes dziļums	18 mm
Lietotņu vadība, izmantojot Bluetooth	No
Nominālās jaudas pretestības slodze	400 W
Nominālās jaudas induktīvā slodze	400 VA
Nominālās jaudas kapacitatīvā slodze	400 VA
Savietojams ar Apple HomeKit	No
Savietojams ar Google palīgu	No
Savietojams ar Amazon Alexa	No

Without N connection, POWER MOSFET up to 400W. Standby loss 0.5 watt only. With control inputs for pushbutton light switches and light switches. With adjustable minimum brightness and ­dimming speed. Built-in device for installation. 45mm long, 45mm wide, 18mm deep. Universal dimmer switch for R, L and C loads up to 400 watt, depending on ventilation conditions. Automatic detection of load R+L or R+C. Not compatible with 230V LED and energy saving lamps, please use the EUD61NPL or the dimmer with N connection: EUD61NPN. Zero passage switching with soft start and soft OFF to protect lamps. Control voltage 230V. Min. load 20W. Short-time control commands switch on/off, permanent control varies the brightness up to the maximum level. A short interruption of control changes the direction of dimming. The brightness level is stored after switching off. In case of a power failure the switching position and the brightness level are stored. If applicable the dimmer will be switched on at the stored brightness level after the supply voltage is recovered. Automatic electronic overload protection and over-temperature switch-off. The minimum brightness level (completely dimmed down) can be adjusted with the upper rotary switch %lamp. The dimming speed can be adjusted with the lower dimming speed rotary switch. Simultaneously the soft on and soft off period is changed. If light switches cannot be replaced by pushbutton light switches, there is a separate control input for light switches. If the switch is opened briefly after closing, the light is dimmed until the next time it is opened again briefly. The dimming direction changes automatically at both peaks. The dimming direction can also be changed by opening the switch briefly twice. Switching operation for children's rooms (only if controlled by pushbutton light switch): If the light is switched on by holding down the pushbutton, it starts at the lowest brightness level after approx. 1 second and dims up slowly as long as the pushbutton is held down without modifying the last stored brightness level. Snooze function (only if controlled by pushbutton light switch): With a double impulse the lighting is dimmed down from the current dimming position to the minimum brightness level and switched off. The current dimming position as well as the adjustable minimum brightness level determine the dimming time (max. = 60 minutes) which can be reduced as required. It can be switched off at any time by short-time control commands during the lighting is dimmed down. Holding down the pushbutton during the dimming down process dims up and stops the snooze function. Without N connection, therefore suitable for mounting directly behind the pushbutton light switch or light switch, even if no N wire is available. Mixing of L loads (inductive loads, e.g. wound transformers) and C loads (capacitive loads, e.g. electronic transformers) is not permitted. R loads (ohmic loads, e.g. 230V incandescent lamps and halogen lamps) may be added anytime.