Wireless actuator constant current LED dimmer switch

Preces stāvoklis	Jauns
Ražotāja nosaukums	Wireless actuator constant current LED dimmer switch
Zīmols	ELTAKO
Kategorijas	Sensori
Izcelsmes valsts	CN
Harmonizētās sistēmas kods	8526 9200 00
Montāžas metode	Virsmas montāža (apmetums)
Modelis	Blīvēšanas piedziņa
Izvadu skaits	1
Biežums	50 Hz
Autobusu sistēma KNX	No
Autobusu sistēmas radio bieži	Yes
Autobusu sistēma Powernet	No
Ar autobusa savienojumu	No
Slodzes veids	Kapacitatīvais
spriegums	12-36 V
Citas autobusu sistēmas	Nav
Autobusu sistēma LON	No
Apakšstacijas ieeja	No
Iespējama paralēlā apkalpošana	No
Vietējā darbība/rokas darbība	No
Izejas jauda	30 W
Aizsardzības pakāpe (IP)	IP20
Ar LED indikāciju	No
Piemērots jaudas palielinājums	No
Autobusu sistēma KNX radio	No
Radio bieži divvirzienu	Yes
Autobusa modulis noņemams	No
Min. iebūvētās instalācijas kastes dziļums	33 mm

Iepakojuma līmenis 1	4010312314357, 4010312314357
Iepakojuma līmenis 2	4010312314357
Iepakojuma līmenis 3	4010312314357

DC constant current source for LEDs up to 1000mA or 30 watts. Only 0.3 watt standby loss. With adjustable minimum brightness and dimming speed. With switching operation for children's rooms and snooze function. Also with light scene control by PC or wireless pushbuttons. Encrypted wireless and repeater function are switchable. For installation. 45mm long, 45mm wide, 33mm deep. The nominal output current can be set with a jumper on the circuit board: no connection: 350mA, flush right (Pin 2-3 connected): 700mA, flush left (Pin 1-2 connected): 1000mA. Factory settings 700mA. The input voltage ranges from 12V DC to 36V DC maximum. The input voltage must be selected to the sum of the LED at the output voltage, so that the current control can operate. This deviation must be at least 6 volts. The total power output current x output voltage should not exceed 30 watts. A pulse resistant DC power supply unit is required, which provides the necessary voltage and required current of the LED light(s). Universal control voltage input 8 to 230V UC, electrically isolated from the 230V supply voltage and switching voltage. The brightness level is stored on switch-off (memory). In case of a power failure the switch position and the brightness stage are stored and may be switched on when the power supply is restored. Automatic electronic overload protection and overtemperature switch-off. You can teach in encrypted sensors. You can switch on bidirectional wireless and/or a repeater function. The minimum brightness (fully dimmed) is adjustable with the upper %lamp rotary switch. In the setting LRN up to 35 pushbuttons can be assigned, of which one or more central pushbuttons. The dimming speed can be adjusted with the lower dimming speed rotary switch. In addition to the wireless control input via an internal antenna, this universal dimmer switch can also be controlled locally by a conventional 230V control switch if fitted previously. A short interruption of control changes the direction of dimming. Short control commands switch on/off. The pushbuttons can be either taught-in as direction pushbuttons or universal pushbuttons: As direction pushbutton switch on and dim up is on one side and switch off and dim down on the other side. A double-click on the switch on side triggers the automatic dimming up to full brightness with dim speed time. A double-click on the switch off side triggers the snooze function. The children's room function is triggered on the switch on side. As a universal pushbutton the direction change is made by briefly releasing the pushbutton. With switching operation for children's rooms and snooze function. Central pushbutton on switches on with memory value. Central pushbutton off switches off. Switching operation for children's rooms (universal pushbutton or direction pushbutton on the switch-on side): If the light is switched on by holding down the pushbutton, it starts at the lowest brightness level after approx. 1 second and dims up slowly as long as the pushbutton is held down without modifying the last stored brightness level. Snooze function (universal pushbutton or direction pushbutton on the switch-off side): With a double impulse the lighting is dimmed down from the current dimming position to the minimum brightness level and switched off. The current dimming position as well as the adjustable minimum brightness level determine the dimming time (max. = 60 minutes) which can be reduced as required. It can be switched off at any time by short-time control commands during the lighting is dimmed down. Light scenes via app are set and retrieved using the Professional Smart Home controller. Lights scenes with wireless pushbuttons are taught in on the FKLD61 device. Up to four brightness values which can be taught-in in light scene pushbuttons with double rocker. A FBH can either be taught-in as a movement detector with/without twilight switch or a FAH as a twilight switch according to the operating instructions. The LED performs during the teach-in process according to the operating instructions. It shows wireless control commands by short flickering during operation.