Wireless actuator multifunction impulse switch, 1+1 NO contacts 10A

Preces stāvoklis	Jauns
Ražotāja nosaukums	Wireless actuator multifunction impulse switch, 1+1 NO contacts 10A
Zīmols	ELTAKO
Kategorijas	Gaismas slēdži
Izcelsmes valsts	CN
Harmonizētās sistēmas kods	8526 9200 00
Montāžas metode	Iebūvējams vienā līmenī (apmetums)
Krāsa	Zils
Nesatur halogēnus	Yes
Virsmas aizsardzība	Citi
Pašreizējais piedāvājums	230 V MAIŅSTRĀVA
Releju skaits	2
Piemērots slēdzim	Yes
Piemērots pulsa pogai	Yes
Piemērots dimmeram	No
Piemērots rullo slēģu slēdzim	No
Materiāla kvalitāte	Termoplasts
Materiāls	Plastmasas
Stiprinājuma veids	Citi
Ritošā koda sistēma	Yes
Komandu skaits	32
Radio frekvences	868 MHz
Mājoklī	Yes
Caurules pamatnes korpusā	No
Iespiedshēmas plate/modulis	No
Spiedpogas režīms	Yes
Pārslēgšanas režīms	Yes
Ar manuālo radio raidītāju	No
Ar radio kodēšanas ierīci	No
Ar radio vadāmu spiedpogu	No
Piemērots venēcisko/rullo slēģu slēdzim	No
Piemērots Venēcijas slēģu slēdzim	No
Caurspīdīgs	No
Virsmas apdare	Matt
Piemērots aizsardzības pakāpei (IP)	IP20
Ir pieejams IFTTT atbalsts	No
Savietojams ar Apple HomeKit	No
Savietojams ar Google palīgu	No
Savietojams ar Amazon Alexa	No

Iepakojuma līmenis 1	4010312300268, 4010312300268
Iepakojuma līmenis 2	4010312300268
Iepakojuma līmenis 3	4010312300268

1+1 NO contacts not potential free 10A/250V AC, 230V LED lamps up to 400W, incandescent lamps up to 2000 watts. Encrypted wireless, bidirectional wireless and ­repeater function are switchable. Only 0.8 watt standby loss. For installation. 45mm long, 45mm wide, 33mm deep. Supply voltage, switching voltage and control voltage local 230V. If a power failure occurs, the switching state is retained. If a power failure occurs repeatedly, the device is switched off in a defined sequence. This wireless actuator is a multifunction impulse switch and features state-of-the-art hybrid technology that we developed: we combined the wear-free receiver and evaluation electronics and two bistable relays with zero passage switching. By using a bistable relay coil power loss and heating is avoided even in the on mode. After installation, wait for short automatic synchronisation before the switched consumer is connected to the mains. In addition to the wireless control input via an internal antenna, this multifunction impulse switch can also be controlled locally by a conventional 230V control switch previously mounted (in the 2xS function only contact 1). Maximum current as the sum of both contacts 16A at 230V. You can teach in encrypted sensors. You can switch on bidirectional wireless and/or a repeater function. Every change in state and incoming central command telegrams are confirmed by a wireless telegram. This wireless telegram can be taught-in in other actuators, Professional Smart Home controllers and in universal dis­plays. With the top rotary switch in the setting LRN up to 35 wireless pushbuttons can be assigned, of which one or more central control pushbuttons. The required function of this multifunction impulse switch can then be selected. Switching will be visualised by flashing of the LED. 2xS = 2fold impulse switch each with 1 NO contact. 2S = impulse switch with 2 NO contacts. WS = impulse switch with 1 NO contact and 1 NC contact. SS1 = impulse multicircuit switch 1 + 1 NO contact with switching sequence 1. SS2 = impulse multicircuit switch 1 + 1 NO contact with switching sequence 2. Switching sequence SS1: 0 - contact 1 - contact 2 - contacts 1+2. Switching sequence SS2: 0 - contact 1 - contacts 1+2 - contact 2. The bottom rotary switch is only required to teach-in the transmitters. From production week 08/2013 universal pushbuttons and direction pushbuttons can be taught in. The LED performs during the teach-in process according to the operating instructions. It shows wireless control commands by short flickering during operation.