Wireless weather data transmitter module

Preces stāvoklis	Jauns
Ražotāja nosaukums	Wireless weather data transmitter module
Zīmols	ELTAKO
Kategorijas	Gaismas slēdži
Izcelsmes valsts	CN
Harmonizētās sistēmas kods	8526 9200 00
Pašreizējais piedāvājums	Citi
Diapazons	30 m
Ritošā koda sistēma	No
Iebūvējams radio raidītājs	No
Virsmas uzstādīts radio raidītājs	Yes
Tastatūras aizsargvāciņš	No
Radio frekvences	868 MHz
Ar manuālo radio raidītāju	No
Ar radio kodēšanas ierīci	No
Aizsardzības pakāpe (IP)	IP20

Iepakojuma līmenis 1	4010312301937, 4010312301937
Iepakojuma līmenis 2	4010312301937
Iepakojuma līmenis 3	4010312301937

Wireless weather data transmitter module for the seven weather items sent by the multisensor MS. With internal antenna. Only 0.3 watt standby loss. For installation. 45mm long, 45mm wide, 18mm deep. Power (24V DC) is supplied by the switch mode power supply unit SNT61-230V/24V DC-0,25A (33mm deep, 45mm long, 45mm wide). This switching power supply unit simultaneously supplys the multisensor MS including the heating of the rain sensor. It is possible to use a deep UP box for the two devices. This weather data transmitter module receives the seven momentary readings of the weather items: brightness (from three cardinal points), twilight, wind, rain and ambient temperature by cable J-Y (ST) Y 2x2x0,8 from the multisensor MS attached to the outside of the building. The readings are sent in the form of wireless telegrams over the Eltako wireless network with the priorities listed below. Only one MS multisensor can be connected to a wireless weather data transmitter module FWS61. However, several FWS61 can be connected to a multisensor MS. The external terminating resistor has to be present on only one FWS61. If there are other FWS61, it must be removed. The evaluation is made with a Professional Smart Home controller, the wireless multifunction sensor relay FMSR14, or the actuators FSB14 and FSB71. When the supply voltage is applied, a teach-in telegram is sent immediately and two status telegrams containing the momentary values are sent approx. 60 seconds later. At least every 10 minutes, but also: Brightness values West, South and East each from 0 to 99 kLux if a change of minimum 10% occurs. Twilight values from 0 to 999 Lux if a change of minimum 10% occurs. Wind speeds from 0 to 70m/s. From 4m/s to 16m/s, the momentary values are sent immediately 3 times at intervals of 1 second. After that, further value increases are sent within 20 seconds. Dropping wind speeds are sent progressively delayed by 20 seconds. Rain values at the start are sent immediately 3 times. After the rain stops, a telegram is sent within 20 seconds. Temperature values from -40.0°C to +80.0°C are sent every 10 minutes together with all the other values in a status telegram. Monitoring multisensor function and line break. If the weather data message from multisensor MS is not sent for 5 seconds, the FWS61 immediately sends an alarm telegram which is repeated every 30 seconds. The alarm telegram can be taught-in as a switch telegram in an actuator to initiate further action as required. In addition, the two status telegrams containing the values brightness 0Lux, twilight 0Lux, temperature -40°C (frost), wind 70m/s and rain are sent. When a message is again detected from the multisensor MS, the alarm stops automatically.