Reģistrējieties, lai atbloķētu savas ekskluzīvās B2B cenas un sāktu iepirkties. Reģistrējieties tagad!
Coupling relay, 1 NO contact 16A
Ir noliktavā: Nē
Piegādātāja krājumi: Nē
Minimālais pasūtījuma daudzums: 1
Cena (bez PVN):
45,05 €
EAN: 4010312206683
MPN: 22100800
Iepakojums: 1
Technical Information
| Preces stāvoklis | Jauns |
| Ražotāja nosaukums | Coupling relay, 1 NO contact 16A |
| Zīmols | ELTAKO |
| Kategorijas |
Releji |
| Izcelsmes valsts | CN |
| Harmonizētās sistēmas kods | 8536 4900 00 |
| Montāžas metode | DIN sliede |
| Funkcija | Daļēji elektronisks |
| Iebūvēts dziļums | 58 mm |
| Nominālā strāva | 16 A |
| Platums moduļu atstarpju skaitā | 1 |
| Vadības spriegums 1 | 8-230 V |
| Vadības sprieguma veids 1 | AC/DC |
| Frekvences vadības spriegums 1 | 50 Hz |
| Maks. pārslēgšanas strāva (cos phi = 0,6) | 4 A |
| Maks. kvēlspuldžu slodze | 2000 W |
| Maks. slodzes dienasgaismas spuldze | 1000 VA |
| Maks. slodzes dienasgaismas spuldze (Duo ķēde) | 1000 VA |
| Maks. slodzes dienasgaismas spuldze (paralēli kompensēta) | 500 VA |
| Kontaktu skaits kā parasti slēgtam kontaktam | 0 |
| Kontaktu skaits kā parasti atvērtam kontaktam | 1 |
| Kontaktpersonu skaits kā maiņas kontaktpersona | 0 |
Iepakojuma informācija
| Iepakojuma līmenis 1 | 4010312206683, 4010312206683 |
| Iepakojuma līmenis 2 | 4010312206683 |
| Iepakojuma līmenis 3 | 4010312206683 |
Lejupielādes
Apraksts
1 NO contact potential free 16A/250V AC with tungsten pre-contact, max. inrush current 500A/2ms. 230V LED lamps up to 600W, incandescent lamp load 3300W. No standby loss. Modular device for DIN-EN 60715 TH35 rail mounting. 1 module = 18mm wide, 58mm deep. State-of-the-art hybrid technology combines advantages of nonwearing electronic control with high capacity of special relays. With the patented Eltako Duplex technology (DX) the normally potential-free contacts can still switch in zero passage when switching 230V AC 50Hz and therefore drastically reduce wear. Simply connect the neutral conductor to the terminal (N) and L to 1(L) for this. This gives an standby consumption of only 0.1 watt. If the contact is used for controlling switching devices which do not perform zero passage switching themselves, (N) should not be connected because the additional closing delay otherwise causes the opposite effect. Universal control voltage 8 to 230 V UC. Low switching noise. Contact position indicator with LED. By using a bistable relay coil power loss and heating is avoided even in the on mode. The relay contact can be open or closed when putting into operation. It will be synchronised at first operation. This relay is not suitable to feed back the switching voltage signal of a dimmer switch. Use only relays ESR12DDX-UC, ESR12NP-230V+UC or ESR61NP-230V+UC for this purpose. The electronics does not have an internal power supply and therefore no standby loss. The microcontroller is activated when the control contact closes. This switches the bistable relay to the correct direction. The bistable relay switches back either when the control contact opens or when the control voltage falls.