Digital settable multifunction time relay, 1 CO contact 10A

Preces stāvoklis	Jauns
Ražotāja nosaukums	Digital settable multifunction time relay, 1 CO contact 10A
Zīmols	ELTAKO
Kategorijas	Releji
Izcelsmes valsts	CN
Harmonizētās sistēmas kods	8536 4900 00
Montāžas metode	DIN sliede
Funkcija	Daudzfunkcionāls
Iebūvētais augstums	58 mm
Uzbudinājuma veids	Digitāls ar multifunkciju
Platums moduļu atstarpju skaitā	1
Pārslēgšanas slēdžu skaits	1
Vadības spriegums 1	8-230 V
Vadības sprieguma veids 1	AC/DC
Frekvences vadības spriegums 1	50 Hz
Barošanas sprieguma sprieguma veids	AC/DC
Barošanas spriegums	8-230 V
1. intervāla vienība	Minūtes/ stundas
1. intervāls	0.1-40
Slēdža jaudas kvēlspuldzes	2000 W
Slēdža jaudas dienasgaismas spuldze DUO	1000 VA
Slēdža jaudas dienasgaismas spuldze induktīva	1000 VA
Slēdža jaudas dienasgaismas spuldze paralēli	500 VA
Kontaktu skaits kā parasti slēgtam kontaktam	0
Kontaktu skaits kā parasti atvērtam kontaktam	0

Iepakojuma līmenis 1	4010312603079, 4010312603079
Iepakojuma līmenis 2	4010312603079
Iepakojuma līmenis 3	4010312603079

1 CO contact potential free 10A/250V AC. 230V LED lamps up to 200W, incandescent lamps 2000W*. Standby loss 0.05–0.5 watt only. Modular device for DIN-EN 60715 TH35 rail mounting. 1 module = 18mm wide, 58mm deep. With the patented Eltako Duplex technology (DX) the normally potential-free contacts can still switch in zero passage when switching 230V AC 50Hz and therefore drastically reduce wear. Simply connect the neutral conductor to the terminal (N) and L to 15(L) for this. This gives an additional standby consumption of only 0.1 Watt. Universal control voltage 8 to 230V UC. Supply voltage same as the control voltage. Both functions and times are entered at the touch of a key and indicated digitally on an LC display. Only two keys are required for this purpose. When setting the time all values can be entered within preset time ranges (0.1 to 9.9 or 1 to 99 seconds, minutes or hours). The longest possible setting is 99 hours. 600 settings are possible. The time setting is continuously displayed digitally. By using a bistable relay coil power loss and heating is avoided even in the on mode. The switched consumer may not be connected to the mains before the short automatic synchronisation after installation has terminated. Functions: RV = off delay. AV = operate delay. AV+ = operate delay additive. TI = clock generator starting with impulse. TP = clock generator starting with pause. IA = impulse controlled pickup delay (e.g. automatic door opener). IF = pulse shaper. EW = fleeting NO contact. AW = fleeting NC contact. With TI, TP, IA, EAW, ARV and ARV+ functions, a different second time can be entered also with different time ranges. Setting the times and functions: The LCD component to be changed is selected by pressing the MODE key. The component accessed flashes. Press the SET key to change the component accessed. This may be the function, the time ranges, time T1 or time T2 (on TI, TP, IA, EAW, ARV and ARV+ only). Pressing the MODE key terminates each input. Once the time has been set with MODE, no more components are flashing. The timing relay is now ready to operate. Press the MODE key again to restart the input cycle. All the entered parameters are retained if they are not changed using SET. 25 sec. after the last operation and if the component still flashes the input cycle is automatically terminated and the previously made changes lapse. Functions of the LC display: If the ON or OFF function was selected, no time is displayed, only ON and OFF and a contact symbol in the correct position. On all other functions, the set time, the function code and the contact symbol are shown in the correct position (open or closed).The clock symbol flashes while the set time is elapsing and the remaining time is shown. Safety in the event of a power failure: The set parameters are stored in an EEPROM and are therefore immediately available again when the power supply is restored after a power failure. * The maximum load can be used starting at a delay time or clock cycle of 5 minutes. The maximum load will be reduced for shorter times as follows: up to 2 seconds 15%, up to 2 minutes 30%, up to 5 minutes 60%.