1-10V controller for universal dimmer switches, 1 NO contact 600VA

Preces stāvoklis	Jauns
Zīmols	ELTAKO
Kategorijas	Gaismas slēdži
Izcelsmes valsts	CN
Harmonizētās sistēmas kods	8536 5080 00
Montāžas izkārtojums	Citi
Darbības metode	Skārienkontroles poga
Slodzes veids	Kapacitatīvā slodze
Ierīces platums	18 mm
Ierīces augstums	58 mm
Ierīces dziļums	66 mm

Iepakojuma līmenis 1	4010312108116, 4010312108116
Iepakojuma līmenis 2	4010312108116
Iepakojuma līmenis 3	4010312108116

Montāžas metode	DRA (adapteris uz DIN sliedes)
Krāsa	Zils
Nesatur halogēnus	Yes
Savienojuma veids	Skrūvējams termināls
Virsmas aizsardzība	Citi
Materiāla kvalitāte	Termoplasts
Materiāls	Plastmasas
Stiprinājuma veids	Citi
Gaismas vērtību atmiņa	No
Apakšstacijas ieeja	No
Sērijveida dimmer	No
Piemērojams ar kustību sensoru	No
Piemērojams ar pārraides pogu	No
Piemērojams ar infrasarkano pogu	No
Piemērojams ar klātbūtnes indikatoru	No
Piemērojams ar pogu	Yes
Piemērojams ar laika slēdzi/taimeri	No
Vadības spriegums	8-230 V
Caurspīdīgs	No
Virsmas apdare	Matt
Serdes šķērsgriezums	6 mm²
Ir pieejams IFTTT atbalsts	No
Aptumšošanas fāzes atslēgšana	No
Aptumšošanas fāzes pārslēgšana	No
Lietotņu vadība, izmantojot Bluetooth	No
Savietojams ar Apple HomeKit	No
Savietojams ar Google palīgu	No
Savietojams ar Amazon Alexa	No

1 NO contact potential free 600VA and 1-10V control output 40mA. Standby loss 0.9 watt only. Modular device for DIN-EN 60715 TH35 rail mounting. 1 module = 18mm wide, 58mm deep. State-of-the-art hybrid technology combines advantages of nonwearing electronic control with high capacity of special relays. The controller SUD12 can be used in two different modes: Mode 1-10V output: In this mode electronic ballast units and transformers with a 1-10V interface up to a total control current of 40mA can be controlled when connected to an universal dimmer switch EUD12D or MFZ12PMD. The EUD12D or the MFZ12PMD is controlled with pushbuttons at the universal control voltage input locally or centrally. The SUD12 converts the dimmer signals from Y1/Y2 to the 1-10V output 0/Q1 for the interface. It switches the electronic ballast with a bistable relay at the output EVG (electronic ballast units). Zero passage switching to protect contacts. The switching capacity for ­fluorescent lamps or low voltage halogen lamps with electronic ballast is up to 600VA. By using a bistable relay coil power loss and heating is avoided even in the on mode. The switched load may not be connected to the mains before the short automatic synchronisation after installation has terminated. At the same time a dircectly dimmable lamp can be connected to the dimmer switch EUD12D. Furthermore the dimmer switch EUD12D or MFZ12PMD can be expanded with capacity enhancers LUD12 for directly dimmable lamp. Mode 1-10V input: In this mode the output of a 1-10V controller can be converted at A1/0 into a direct dimming function when ­connected to a capacity enhancer LUD12 at terminals X1/X2. The closing operation and the opening operation is also carried out externally at L of the SUD12. The rotary switch of the LUD12 must be adjusted to the setting two lamps (additional lamps). Further capacity enhancers LUD12 in the mode increase of capacity with additional lamps can be connected to the controller SUD12. A 100K potentiometer for brightness control may also be directly connected to the control input A1/0. If the input A1/0 is disconnected the LUD12 dimms to maximum brightness.