Reģistrējieties, lai atbloķētu savas ekskluzīvās B2B cenas un sāktu iepirkties. Reģistrējieties tagad!
Staircase time switch, 1 NO contact 10A image 1

Staircase time switch, 1 NO contact 10A

Ir noliktavā: Nē Piegādātāja krājumi: Nē Minimālais pasūtījuma daudzums: 1
Cena (bez PVN):
36,05 €
Šī cena ir spēkā līdz 31.12.24
EAN: 4010312400791
MPN: 61100102
Iepakojums: 1

Technical Information

Preces stāvoklis Jauns
Ražotāja nosaukums Staircase time switch, 1 NO contact 10A
Zīmols ELTAKO
Kategorijas Releji
Izcelsmes valsts CN
Harmonizētās sistēmas kods 8536 5080 00
Montāžas metode Iebūvējams vienā līmenī (apmetums)
Funkcija Elektronisks ar izslēgšanas brīdinājuma signālu
Iebūvēts dziļums 18 mm
Atbrīvošana-aizkavēšanās 1-12 min
Platums moduļu atstarpju skaitā 0
Vadības spriegums 1 230 V
Vadības sprieguma veids 1 AC
Frekvences vadības spriegums 1 50 Hz
Elektroinstalācijas sistēma 3 un 4 vadu konfigurācija
Iepriekšējs brīdinājums par izslēgšanos Mirgošana
Atkārtojas Atkārtota + nepārtraukta gaisma + laika pagarinājums
Barošanas sprieguma sprieguma veids AC
Barošanas spriegums 250 V
Maks. kvēlspuldžu slodze 2000 W
Maks. slodzes dienasgaismas spuldze 1000 VA
Maks. slodzes dienasgaismas spuldze (Duo ķēde) 1000 VA
Maks. slodzes dienasgaismas spuldze (paralēli kompensēta) 500 VA
Nominālā slēdža strāva 10 A
Spiedpogas kvēlspuldzes strāva 50 mA
Atlasāma strāvas pārsprieguma funkcija No
Kontaktu skaits kā parasti slēgtam kontaktam 0
Kontaktu skaits kā parasti atvērtam kontaktam 1
Kontaktpersonu skaits kā maiņas kontaktpersona 0
Maks. pārslēgšanas jaudas LED 200 W

Iepakojuma informācija

Iepakojuma līmenis 1 4010312400791, 4010312400791
Iepakojuma līmenis 2 4010312400791
Iepakojuma līmenis 3 4010312400791

Lejupielādes

Apraksts

1 NO contact not potential free 10A/250V AC. 230V LED lamps up to 600W, energy saving lamps ESL up to 200W, incandescent lamps up to 2000W. Switch-off early warning and permanent light by pushbutton switchable. Standby loss 0.7 watt only. With ESL optimisation. Built-in device for installation. 45mm long, 45mm wide, 18mm deep. Zero passage switching to protect contacts and lamps. By using a bistable relay coil power loss and heating is avoided even in the on mode. The switched consumer may not be connected to the mains before the short automatic synchronisation after installation has terminated. Control voltage, supply voltage and switching voltage 230V. With infinitely variable time range from 1 to 12 minutes. 50mA glow lamp current, dependent on the ignition voltage of the glow lamps. 3-wire and 4-wire circuits, resettable, with attic lighting if 4-wire circuit. Automatic detection of the method of connection. After a power failure the lighting is switched on again in case the set time has not elapsed yet. If switch-off early warning function is switched on, the light starts flickering approx. 30 seconds before time-out and is repeated three times at decreasing time intervals. If permanent light by pushbutton is switched on, permanent light can be switched on by pressing the pushbutton longer than 1 second. This is switched off automatically after 60 minutes or by pressing the pushbutton longer than 2 seconds. If both switch-off early warning function and permanent light by pushbutton   are switched on, the switch-off early warning function is activated before the permanent light switches off. When energy saving lamps ESL are completely or partially switched, then set the switch-off early warning with the pushbutton permanent light ESL on the lower rotary switch. If the function TLZ is selected the time can be extended within the first second after switching on or resetting by pressing the pushbutton repeatedly up to three times (incrementing). Each momentary-contact control increments the set time once. The function ESV, impulse switch with release delay up to 120 minutes, can be selected optionally. If this function is set it is automatically disconnected after the set delay is timed out if a manual OFF command has not been given. If the timing period is set to minimum in the function ESV, the release delay is switched off. The standard impulse switch function ES is then set.