DALI Phase dimmer 300W for ceiling installation (DT4)

Toote seisukord	Uus
Tootja nimi	DALI Phase dimmer 300W for ceiling installation (DT4)
Bränd	ELTAKO
Kategooriad	Lülitid
Päritoluriik	BG
Harmoneeritud süsteemi kood	8542 3190 00
Kooste ehitus	Põhielement
Talitlusviis	Muul viisil
Nimipinge	230 V
Sobib vastava kaitseastme (IP) korral	IP20
Laius	30 mm
Kõrgus	120 mm
Seadme sügavus	22 mm
Max. switching power LED	300 W

Pakkimistase 1

4010312324028, 4010312324028

Paigaldusviis	Muul viisil
Värvus	Hall
Halogeenivaba	Yes
Ühenduse liik	Pistikuklamber
Pinnatöötlus	Töötlemata
Materjal	Termoplastist
Materjal	Plast
Kinnitusviis	Muul viisil
Valgustatuse mälu	Yes
Alajaama sisend	No
Serial dimmer	No
Rakendatav koos liikumisanduriga	No
Rakendatav koos edastuslülitiga	No
Rakendatav koos infrapunalülitiga	No
Rakendatav koos olemasolu indikaatoriga	No
Rakendatav koos nupplülitiga	No
Rakendatav koos aeglüliti/taimeriga	No
Juhtimispinge	9.5-22.5 V
Läbipaistev	No
Pinna liik	Matt
Südamiku ristlõige	0.5-1.5 mm²
Saadaval on rakenduste IFTTT sobitustugi	No
Reguleerimine, faasi väljalülitamine	Yes
Reguleerimine, faasi sisselülitamine	Yes
Sisseehitatud paigalduskarbi vähim sügavus	22 mm
Rakenduse juhtimine sinihambaga (Bluetooth)	No
Nominal power resistive load	300 W
Nominal power inductive load	300 VA
Nominal power capacitive load	300 VA
Compatible with Apple HomeKit	No
Compatible with Google Assistant	No
Compatible with Amazon Alexa	No

Phase dimmer with DALI control input for ceiling installation 120x30x22mm. Protection class IP20. Suitable for dimming 230V LED retrofit ­luminaries using DALI. Converts DALI dimming level to a voltage with leading or trailing edge. The minimum dimming level (MIN LEVEL) is adjustable via DALI. Additional operating mode as switch (conforms to DT7) as from Firmware 3.5. The module represents a bus user and is therefore addressable. Double terminals for easy looping of the DALI bus. Dimming range 0.1%-100%. Supply voltage 230V AC. Output load range 10-300W. High efficiency. Configuration via DALI Cockpit PC software. Function: The DALI PD is an interface between classic dimming technology (phase dimming) and DALI which is based on the standard for DALI Control Gear (IEC 62386-102) and Device Type 4 equipment (IEC 62386-205). The DALI PD interface converts the required dimming level into a corresponding voltage signal with leading or trailing edge. Depending on the load the universal dimmer operates as a leading or trailing edge dimmer. The operating mode can be requested over DALI (DT4). The dimming characteristic is based on a logarithmic scale as stipulated in the DALI standard. The leading or trailing edge control supplies a sinusoidal voltage with a phase-cut on the leading or trailing edge. The PHYSICAL MINLEVEL is 3%. As of Firmware version 3.5 the DALI PD is equipped with an additional operating mode. It is switchable from DT4 operating mode (phase dimming) to DT7 (switch). In this ­operating mode the DALI PD acts as a switch. Its behaviour in this mode corresponds to the DALI standard for DT7 devices (IEC62386-208). In this operating mode the switch characteristic is determined by comparing the virtual dim level (VDAP) with 4 switching thresholds. The virtual dim level (VDAP) corresponds to the dim level of a DALI electronic ballast with its corresponding characteristics (limited by MINLEVEL and MAXLEVEL, dimming speed limited by fade time and fade rate). There are 2 switching thresholds in each dimming direction and they are used for comparison with the virtual dim level: A threshold with the value 'MASK' is inactive and is not used in the comparison. Switch-on/off delays can be implemented with fading. The device is powered from the DALI bus so that there is only partial support for the SYSTEM FAILURE LEVEL. On current devices (identified by Firmware > 4.0), you can choose between 0%,100% and MASK. On older models the SYSTEM FAILURE LEVEL is fixed - the 25W variant outputs 100%. The 300W variant outputs 0%.