DALI Phase dimmer 300W for ceiling installation (DT4)

Preces stāvoklis	Jauns
Ražotāja nosaukums	DALI Phase dimmer 300W for ceiling installation (DT4)
Zīmols	ELTAKO
Kategorijas	Gaismas slēdži
Izcelsmes valsts	BG
Harmonizētās sistēmas kods	8542 3190 00
Montāžas izkārtojums	Pamata elements
Darbības metode	Citi
Nominālais spriegums	230 V
Piemērots aizsardzības pakāpei (IP)	IP20
Ierīces platums	30 mm
Ierīces augstums	120 mm
Ierīces dziļums	22 mm
Maks. pārslēgšanas jaudas LED	300 W

Iepakojuma līmenis 1

4010312324028, 4010312324028

Montāžas metode	Citi
Krāsa	Pelēks
Nesatur halogēnus	Yes
Savienojuma veids	Iebīdāma skava
Virsmas aizsardzība	Neapstrādāts
Materiāla kvalitāte	Termoplasts
Materiāls	Plastmasas
Stiprinājuma veids	Citi
Gaismas vērtību atmiņa	Yes
Apakšstacijas ieeja	No
Sērijveida dimmer	No
Piemērojams ar kustību sensoru	No
Piemērojams ar pārraides pogu	No
Piemērojams ar infrasarkano pogu	No
Piemērojams ar klātbūtnes indikatoru	No
Piemērojams ar pogu	No
Piemērojams ar laika slēdzi/taimeri	No
Vadības spriegums	9.5-22.5 V
Caurspīdīgs	No
Virsmas apdare	Matt
Serdes šķērsgriezums	0.5-1.5 mm²
Ir pieejams IFTTT atbalsts	No
Aptumšošanas fāzes atslēgšana	Yes
Aptumšošanas fāzes pārslēgšana	Yes
Min. iebūvētās instalācijas kastes dziļums	22 mm
Lietotņu vadība, izmantojot Bluetooth	No
Nominālās jaudas pretestības slodze	300 W
Nominālās jaudas induktīvā slodze	300 VA
Nominālās jaudas kapacitatīvā slodze	300 VA
Savietojams ar Apple HomeKit	No
Savietojams ar Google palīgu	No
Savietojams ar Amazon Alexa	No

Phase dimmer with DALI control input for ceiling installation 120x30x22mm. Protection class IP20. Suitable for dimming 230V LED retrofit ­luminaries using DALI. Converts DALI dimming level to a voltage with leading or trailing edge. The minimum dimming level (MIN LEVEL) is adjustable via DALI. Additional operating mode as switch (conforms to DT7) as from Firmware 3.5. The module represents a bus user and is therefore addressable. Double terminals for easy looping of the DALI bus. Dimming range 0.1%-100%. Supply voltage 230V AC. Output load range 10-300W. High efficiency. Configuration via DALI Cockpit PC software. Function: The DALI PD is an interface between classic dimming technology (phase dimming) and DALI which is based on the standard for DALI Control Gear (IEC 62386-102) and Device Type 4 equipment (IEC 62386-205). The DALI PD interface converts the required dimming level into a corresponding voltage signal with leading or trailing edge. Depending on the load the universal dimmer operates as a leading or trailing edge dimmer. The operating mode can be requested over DALI (DT4). The dimming characteristic is based on a logarithmic scale as stipulated in the DALI standard. The leading or trailing edge control supplies a sinusoidal voltage with a phase-cut on the leading or trailing edge. The PHYSICAL MINLEVEL is 3%. As of Firmware version 3.5 the DALI PD is equipped with an additional operating mode. It is switchable from DT4 operating mode (phase dimming) to DT7 (switch). In this ­operating mode the DALI PD acts as a switch. Its behaviour in this mode corresponds to the DALI standard for DT7 devices (IEC62386-208). In this operating mode the switch characteristic is determined by comparing the virtual dim level (VDAP) with 4 switching thresholds. The virtual dim level (VDAP) corresponds to the dim level of a DALI electronic ballast with its corresponding characteristics (limited by MINLEVEL and MAXLEVEL, dimming speed limited by fade time and fade rate). There are 2 switching thresholds in each dimming direction and they are used for comparison with the virtual dim level: A threshold with the value 'MASK' is inactive and is not used in the comparison. Switch-on/off delays can be implemented with fading. The device is powered from the DALI bus so that there is only partial support for the SYSTEM FAILURE LEVEL. On current devices (identified by Firmware > 4.0), you can choose between 0%,100% and MASK. On older models the SYSTEM FAILURE LEVEL is fixed - the 25W variant outputs 100%. The 300W variant outputs 0%.