Wireless shading element and roller shutter actuator

Toote seisukord	Uus
Tootja nimi	Wireless shading element and roller shutter actuator
Bränd	ELTAKO
Kategooriad	Lülitid
Päritoluriik	CN
Harmoneeritud süsteemi kood	8526 9200 00
Paigaldusviis	Süvistatud paigaldus (krohvi)
Värvus	Sinine
Halogeenivaba	Yes
Pinnatöötlus	Muul viisil
Toide	Muul viisil
Releede arv	2
Sobib lülitamiseks	Yes
Sobib impulsslülitiks	Yes
Sobib hämardamiseks	No
Sobib rullsulguri lülitiks	Yes
Materjal	Termoplastist
Materjal	Plast
Kinnitusviis	Muul viisil
Muutuva koodisüsteemiga	Yes
Käskude arv	32
Raadiosagedus	868 MHz
Kestas	Yes
Torukujulises keres	No
Trükiplaat/moodul	No
Nupplülitusmoodus	Yes
Lülitusmoodus	Yes
Käsiraadiosaatja	No
Raadiosignaali kodeerimisseade	No
Raadiosignaaliga juhitava nupplülitiga	No
Sobib ribikardinate lülitiks	Yes
Sobib ribikardinate sulgemiseks	Yes
Läbipaistev	No
Pinna liik	Matt
Sobib vastava kaitseastme (IP) korral	IP20
Saadaval on rakenduste IFTTT sobitustugi	No
Compatible with Apple HomeKit	No
Compatible with Google Assistant	No
Compatible with Amazon Alexa	No

Pakkimistase 1	4010312319406, 4010312319406
Pakkimistase 2	4010312319406
Pakkimistase 3	4010312319406

Wireless shading element and roller shutter actuator 1+1 NO contact, 4A/36V DC, not potential free, for a shading element motor 12-36V DC. Standby loss only 0.3-0.5 watt. For installation. 49x51mm wide, 20mm deep. The terminals are plug-in terminals for conductor cross-sections of 0.2mm2 to 2.5mm2. The convenient tap technology permits the teach-in of up to 32 wireless universal pushbuttons, wireless direction pushbuttons and wireless central control pushbuttons. Bidirectional wireless switchable. Supply voltage, switching voltage and control voltage local 12-36V DC. If supply voltage fails, the device is switched off in defined mode. In addition to the wireless control input via an internal antenna, this wireless actuator can also be controlled locally by a conventional control switch if fitted previously. Control is either by separate local control inputs for Up and Down as direction pushbuttons or these two inputs are bridged and controlled by single pushbuttons as universal pushbuttons. A change in direction then takes place by interrupting activation. An incandescent lamp current is not permitted. Wireless pushbuttons can be taught in with either the functions Up-Stop-Down-Stop as universal pushbuttons or as local pushbuttons as well as a wireless pushbutton or roller shutter double push­buttons can be taught in as direction pushbuttons with press top for Up and bottom for Down. Press briefly to stop the movement. In addition, the central control button can be taught in with static priority. The static priority is only active as long as the radio button is pressed. With a control signal, e.g. B. a radio transmitter module FSM61 with switches that has been taught-in as a central control button, the switching position Up or Down and the priority are specifically activated. With priority because these control signals cannot be overridden by other control signals until the central command is canceled again by the end of the control signal. The tap reverse function can be activated: universal pushbuttons, direction pushbuttons and wired pushbuttons are intially in static mode so that the position of the blind can be adjusted. Switched to dynamic only after activation > 1 second. With control via Professional Smart Home controller, operating commands for up and down with the exact travel time information can be started. As the actuator reports the exact elapsed time after each activity, even when driving was triggered by a pushbutton, the position of the shading is always displayed correctly in the Professional Smart Home controller. Upon reaching the end positions above and below the position is automatically synchronized. When a wireless window contact is taught in, a lockout protection is set up for open windows or doors to disable the Central Down and controller Down commands.