Wireless shading element and roller shutter actuator

Preces stāvoklis	Jauns
Ražotāja nosaukums	Wireless shading element and roller shutter actuator
Zīmols	ELTAKO
Kategorijas	Gaismas slēdži
Izcelsmes valsts	CN
Harmonizētās sistēmas kods	8526 9200 00
Montāžas metode	Iebūvējams vienā līmenī (apmetums)
Krāsa	Zils
Nesatur halogēnus	Yes
Virsmas aizsardzība	Citi
Pašreizējais piedāvājums	Citi
Releju skaits	2
Piemērots slēdzim	Yes
Piemērots pulsa pogai	Yes
Piemērots dimmeram	No
Piemērots rullo slēģu slēdzim	Yes
Materiāla kvalitāte	Termoplasts
Materiāls	Plastmasas
Stiprinājuma veids	Citi
Ritošā koda sistēma	Yes
Komandu skaits	32
Radio frekvences	868 MHz
Mājoklī	Yes
Caurules pamatnes korpusā	No
Iespiedshēmas plate/modulis	No
Spiedpogas režīms	Yes
Pārslēgšanas režīms	Yes
Ar manuālo radio raidītāju	No
Ar radio kodēšanas ierīci	No
Ar radio vadāmu spiedpogu	No
Piemērots venēcisko/rullo slēģu slēdzim	Yes
Piemērots Venēcijas slēģu slēdzim	Yes
Caurspīdīgs	No
Virsmas apdare	Matt
Piemērots aizsardzības pakāpei (IP)	IP20
Ir pieejams IFTTT atbalsts	No
Savietojams ar Apple HomeKit	No
Savietojams ar Google palīgu	No
Savietojams ar Amazon Alexa	No

Iepakojuma līmenis 1	4010312319406, 4010312319406
Iepakojuma līmenis 2	4010312319406
Iepakojuma līmenis 3	4010312319406

Wireless shading element and roller shutter actuator 1+1 NO contact, 4A/36V DC, not potential free, for a shading element motor 12-36V DC. Standby loss only 0.3-0.5 watt. For installation. 49x51mm wide, 20mm deep. The terminals are plug-in terminals for conductor cross-sections of 0.2mm2 to 2.5mm2. The convenient tap technology permits the teach-in of up to 32 wireless universal pushbuttons, wireless direction pushbuttons and wireless central control pushbuttons. Bidirectional wireless switchable. Supply voltage, switching voltage and control voltage local 12-36V DC. If supply voltage fails, the device is switched off in defined mode. In addition to the wireless control input via an internal antenna, this wireless actuator can also be controlled locally by a conventional control switch if fitted previously. Control is either by separate local control inputs for Up and Down as direction pushbuttons or these two inputs are bridged and controlled by single pushbuttons as universal pushbuttons. A change in direction then takes place by interrupting activation. An incandescent lamp current is not permitted. Wireless pushbuttons can be taught in with either the functions Up-Stop-Down-Stop as universal pushbuttons or as local pushbuttons as well as a wireless pushbutton or roller shutter double push­buttons can be taught in as direction pushbuttons with press top for Up and bottom for Down. Press briefly to stop the movement. In addition, the central control button can be taught in with static priority. The static priority is only active as long as the radio button is pressed. With a control signal, e.g. B. a radio transmitter module FSM61 with switches that has been taught-in as a central control button, the switching position Up or Down and the priority are specifically activated. With priority because these control signals cannot be overridden by other control signals until the central command is canceled again by the end of the control signal. The tap reverse function can be activated: universal pushbuttons, direction pushbuttons and wired pushbuttons are intially in static mode so that the position of the blind can be adjusted. Switched to dynamic only after activation > 1 second. With control via Professional Smart Home controller, operating commands for up and down with the exact travel time information can be started. As the actuator reports the exact elapsed time after each activity, even when driving was triggered by a pushbutton, the position of the shading is always displayed correctly in the Professional Smart Home controller. Upon reaching the end positions above and below the position is automatically synchronized. When a wireless window contact is taught in, a lockout protection is set up for open windows or doors to disable the Central Down and controller Down commands.