Register to unlock your exclusive B2B prices. Register now
Staircase time switch, 1 NO contact 10A image 1

Staircase time switch, 1 NO contact 10A

Sandėlyje esančios prekės kaina (be PVM):
37,92 €
Ši kaina galioja iki 2024-12-31
Kaina už m: 37,92 €
EAN: 4010312400739
MPN: 61100301
Mūsų sandėlis: Ne Pardavėjo atsargos: Ne
Už pakuotę: 1 Už dėžę: 1 Už padėklą: N/A
Techniniai duomenys
Prekės būklė Nauja
Gamintojo pavadinimas Staircase time switch, 1 NO contact 10A
Prekės ženklas ELTAKO
Kategorijos Relės
Kilmės šalis CN
Suderintos sistemos kodas 8536 5080 00
Montavimo metodas Apatinis sluoksnis (tinko)
Funkcija Elektroninis su įspėjimu apie išjungimą
Suprojektuotas gylis 18 mm
Atlaisvinimo delsa 1-12 min
Modulinių tarpų skaičius plotyje 0
1 kontrolinė įtampa 230 V
2 kontrolinė įtampa 8-230 V
1 kontrolinės įtampos tipas Kintamoji srovė
2 kontrolinės įtampos tipas Kintamoji ar nuolatinė srovė
1 kontrolinės įtampos dažnis 50 Hz
Laidyno sistema 3 ir 4 laidų konfigūracija
Išjungimo išankstinis įspėjimas Blyksėjimas
Pasikartojantis Pasikartojantis + nuolatinė šviesa + laiko prailginimas
Tiekimo įtampos tipas Kintamoji srovė
Maitinimo įtampos diapazonas 250 V
Maks. kaitrinės lempos apkrova 2000 W
Maks. fluorescencinės lempos apkrova 1000 VA
Maks. fluorescencinės lempos apkrova (dviguba grandinė) 1000 VA
Maks. fluorescencinės lempos apkrova (lygiagrečiai kompensuojama) 500 VA
Nominali jungiklio srovė 10 A
Dujinės lempos srovės paspaudimo mygtukas 50 mA
Parenkamo srovės padidėjimo funkcija No
Įprastai uždarytų kontaktų skaičius 0
Įprastai atvirų kontaktų skaičius 1
Perjungimo kontaktų skaičius 0
Maks. perjungimo maitinimo šviesos diodas 200 W
Pakavimo informacija
Pakavimo lygis 1 4010312400739, 4010312400739
Pakavimo lygis 2 4010312400739
Pakavimo lygis 3 4010312400739
Downloads
Aprašymas
1 NO contact not potential free 10A/250V AC. 230 V LED lamps up to 600W, energy saving lamps ESL up to 200W, incandescent lamps up to 2000W. Switch-off early warning and permanent light by pushbutton switchable. Standby loss 0.7 watt only. With ESL optimisation. Built-in device for installation. 45mm long, 45mm wide, 18mm deep. Zero passage switching to protect contacts and lamps. By using a bistable relay coil power loss and heating is avoided even in the on mode. The switched consumer may not be connected to the mains before the short automatic synchronisation after installation has terminated. Control voltage, supply voltage and switching voltage 230V. In addition electrically isolated universal voltage from 8 to 230V UC. With infinitely variable time range from 1 to 12 minutes. 50mA glow lamp current, dependent on the ignition voltage of the glow lamps. 3-wire and 4-wire circuits, resettable, with attic lighting if 4-wire circuit. Automatic detection of the method of connection. After a power failure the lighting is switched on again in case the set time has not elapsed yet. If switch-off early warning function is switched on, the light starts flickering approx. 30 seconds before time-out and is repeated three times at decreasing time intervals. If permanent light by pushbutton is switched on, permanent light can be switched on by pressing the pushbutton longer than 1 second. This is switched off automatically after 60 minutes or by pressing the pushbutton longer than 2 seconds. If both switch-off early warning function and permanent light by pushbutton   are switched on, the switch-off early warning function is activated before the permanent light switches off. When energy saving lamps ESL are completely or partially switched, then set the switch-off early warning with the pushbutton permanent light ESL on the lower rotary switch. If the function TLZ is selected the time can be extended within the first second after switching on or resetting by pressing the pushbutton repeatedly up to three times (incrementing). Each momentary-contact control increments the set time once. The function ESV, impulse switch with release delay up to 120 minutes, can be selected ­optionally. If this function is set it is automatically disconnected after the set delay is timed out if a manual OFF command has not been given. If the timing period is set to minimum in the function ESV, the release delay is switched off. The standard impulse switch function ES is then set.