Register to unlock your exclusive B2B prices and start shopping. Sign up now!
Staircase time switch, 1 NO contact 10A image 1

Staircase time switch, 1 NO contact 10A

In stock: No Vendor stock: No Minimal order quantity: 1
Price (excl. VAT):
37,92 €
This price is valid until 31.12.24
EAN: 4010312400739
MPN: 61100301
Package: 1

Technical Information

Item condition New
Manufacture name Staircase time switch, 1 NO contact 10A
Brand ELTAKO
Categories Relays
Country of origin CN
Harmonized System Code 8536 5080 00
Mounting method Flush mounted (plaster)
Function Electronic with switching-off pre-warning
Built-in depth 18 mm
Release-delay 1-12 min
Width in number of modular spacings 0
Control voltage 1 230 V
Control voltage 2 8-230 V
Type of control voltage 1 AC
Type of control voltage 2 AC/DC
Frequency control voltage 1 50 Hz
Wiring system 3 and 4 wire configuration
Pre-warning of switching-off Flickering
Repetitive Repetitive + continuous light + time extension
Voltage type of supply voltage AC
Supply voltage 250 V
Max. incandescent lamp load 2000 W
Max. load fluorescent lamp 1000 VA
Max. load fluorescent lamp (Duo circuit) 1000 VA
Max. load fluorescent lamp (parallel compensated) 500 VA
Rated switch current 10 A
Push button glow-lamp current 50 mA
Current surge function selectable No
Number of contacts as normally closed contact 0
Number of contacts as normally open contact 1
Number of contacts as change-over contact 0
Max. switching power LED 200 W

Packing details

Packing level 1 4010312400739, 4010312400739
Packing level 2 4010312400739
Packing level 3 4010312400739

Downloads

Description

1 NO contact not potential free 10A/250V AC. 230 V LED lamps up to 600W, energy saving lamps ESL up to 200W, incandescent lamps up to 2000W. Switch-off early warning and permanent light by pushbutton switchable. Standby loss 0.7 watt only. With ESL optimisation. Built-in device for installation. 45mm long, 45mm wide, 18mm deep. Zero passage switching to protect contacts and lamps. By using a bistable relay coil power loss and heating is avoided even in the on mode. The switched consumer may not be connected to the mains before the short automatic synchronisation after installation has terminated. Control voltage, supply voltage and switching voltage 230V. In addition electrically isolated universal voltage from 8 to 230V UC. With infinitely variable time range from 1 to 12 minutes. 50mA glow lamp current, dependent on the ignition voltage of the glow lamps. 3-wire and 4-wire circuits, resettable, with attic lighting if 4-wire circuit. Automatic detection of the method of connection. After a power failure the lighting is switched on again in case the set time has not elapsed yet. If switch-off early warning function is switched on, the light starts flickering approx. 30 seconds before time-out and is repeated three times at decreasing time intervals. If permanent light by pushbutton is switched on, permanent light can be switched on by pressing the pushbutton longer than 1 second. This is switched off automatically after 60 minutes or by pressing the pushbutton longer than 2 seconds. If both switch-off early warning function and permanent light by pushbutton   are switched on, the switch-off early warning function is activated before the permanent light switches off. When energy saving lamps ESL are completely or partially switched, then set the switch-off early warning with the pushbutton permanent light ESL on the lower rotary switch. If the function TLZ is selected the time can be extended within the first second after switching on or resetting by pressing the pushbutton repeatedly up to three times (incrementing). Each momentary-contact control increments the set time once. The function ESV, impulse switch with release delay up to 120 minutes, can be selected ­optionally. If this function is set it is automatically disconnected after the set delay is timed out if a manual OFF command has not been given. If the timing period is set to minimum in the function ESV, the release delay is switched off. The standard impulse switch function ES is then set.