1 channel DALI LED dimmer 8A for flush-mounted box

Preces stāvoklis	Jauns
Ražotāja nosaukums	1 channel DALI LED dimmer 8A for flush-mounted box
Zīmols	ELTAKO
Kategorijas	Gaismas slēdži
Izcelsmes valsts	BG
Harmonizētās sistēmas kods	8542 3190 00
Montāžas izkārtojums	Pamata elements
Darbības metode	Nospiežamā poga
Nominālais spriegums	12-48 V
Piemērots aizsardzības pakāpei (IP)	IP20
Ierīces platums	33 mm
Ierīces augstums	59 mm
Ierīces dziļums	15 mm
Maks. pārslēgšanas jaudas LED	384 W

Iepakojuma līmenis 1

4010312321515, 4010312321515

Montāžas metode	Citi
Krāsa	Pelēks
Nesatur halogēnus	Yes
Savienojuma veids	Iebīdāma skava
Virsmas aizsardzība	Neapstrādāts
Materiāla kvalitāte	Termoplasts
Materiāls	Plastmasas
Gaismas vērtību atmiņa	Yes
Apakšstacijas ieeja	No
Sērijveida dimmer	No
Piemērojams ar kustību sensoru	No
Piemērojams ar pārraides pogu	No
Piemērojams ar infrasarkano pogu	No
Piemērojams ar klātbūtnes indikatoru	No
Piemērojams ar pogu	Yes
Piemērojams ar laika slēdzi/taimeri	No
Vadības spriegums	9.5-22.5 V
Caurspīdīgs	No
Virsmas apdare	Matt
Serdes šķērsgriezums	1.5 mm²
Ir pieejams IFTTT atbalsts	No
Aptumšošanas fāzes atslēgšana	No
Aptumšošanas fāzes pārslēgšana	No
Min. iebūvētās instalācijas kastes dziļums	15 mm
Lietotņu vadība, izmantojot Bluetooth	No
Nominālās jaudas pretestības slodze	384 W
Savietojams ar Apple HomeKit	No
Savietojams ar Google palīgu	No
Savietojams ar Amazon Alexa	No

1 channel DALI LED dimmer for luminary installation and flush-mounted box. 59x33x15mm. Protection class IP20. Only 0.12 watt standby loss. Designed to control constant voltage LED modules (CV) at operating voltages of 12V to 48V, Sw&Dim or SwitchDim2: Operation via 1 or 2 pushbutton inputs permits brightness control without DALI. Alternatively, corridor function for direct activation with a motion detector. Dimming range 0.1%-100%. Switchable PWM frequency (122Hz/244Hz/488Hz/976Hz). Supply voltage 12V to 48V DC. Max. connected current 8A. High efficiency. Configuration via DALI Cockpit PC software and DALI USB interface. Operating modes: The output channel is controlled by a DALI address (Device Type 6). Alternatively, operation can also take place by one (Sw&Dim) or two pushbutton inputs (SwitchDim2). SwD1, Sw&Dim: brightness. Press pushbutton briefly: On/Off. Press pushbutton long: Dim. SwD2: Scene switch (press pushbutton briefly). If you press the SwD1 input for 2 minutes, the mode changes to Corridor function. This operating mode remains enabled until the device is disconnected from the power supply (after PowerUp: operation via SwD1/SwD2). Corridor function: Mode with integrated staircase time switch (e.g. simple activation of one or several motion detectors by relay contact). When you press the input, the maximum value is switched on. After the input signal decays, the brightness remains at this value for the duration of the hold time before it drops down to the intermediate value. After the hold time for the intermediate value expires, brightness returns to the basic value. The process starts from the beginning when the input is re-activated. The DALI Cockpit software can configure 1-channel LED dimmers. You can define both group assignment and configure scene values and DALI parameters (the parameters displayed are the as-delivered states). As-delivered state: Before the first address is assigned, you can control the device using the group address G0. This preset group assignment is deleted when addresses are assigned. Afterwards, you can define any group assignment in the DALI Cockpit. The values defined in the DALI standard are generated by sending a DALI reset command.