Powerline universal dimmer actuator 1 channel with sensor input 230V

Preces stāvoklis	Jauns
Ražotāja nosaukums	Powerline universal dimmer actuator 1 channel with sensor input 230V
Zīmols	ELTAKO
Kategorijas	Sensori
Izcelsmes valsts	CN
Harmonizētās sistēmas kods	8526 9200 00
Montāžas metode	Iebūvējams vienā līmenī (apmetums)
Modelis	Vadības modulis
Izvadu skaits	1
Biežums	50 Hz
Autobusu sistēma KNX	No
Autobusu sistēmas radio bieži	No
Autobusu sistēma Powernet	Yes
Ar autobusa savienojumu	Yes
Slodzes veids	Universālā
spriegums	230 V
Citas autobusu sistēmas	Nav
Autobusu sistēma LON	No
Apakšstacijas ieeja	No
Iespējama paralēlā apkalpošana	Yes
Vietējā darbība/rokas darbība	Yes
Izejas jauda	600 W
Ar LED indikāciju	Yes
Piemērots jaudas palielinājums	No
Autobusu sistēma KNX radio	No
Radio bieži divvirzienu	Yes
Autobusa modulis noņemams	No
Min. iebūvētās instalācijas kastes dziļums	40 mm
Maks. pārslēgšanas jaudas LED	300 W

Iepakojuma līmenis 1	4010312316870, 4010312316870
Iepakojuma līmenis 2	4010312316870
Iepakojuma līmenis 3	4010312316870

Powerline universal dimmer actuator. 53x43mm, 40mm deep for mounting in 58mm switch boxes. Power MOSFET up to 300W. Automatic lamp detection. Sensor input 230V. Standby loss only 0,6 Watt. To control and dim at the same place. Universal dimmer switch for lamps up to 300W, dependent on ventilation conditions. Dimmable 230V-LED lamps and dimmable energy saving lamps ESL, additionally dependent on the lamps electronics. No minimum load. Zero passage switching with soft ON and soft OFF to protect lamps. Short-time control commands switch on/off, permanent control varies the brightness to the maximum or minimum level. A interruption of control changes the direction of dimming. The brightness level is stored on switch-off (memory). Minimum and maximum brightness can be changed with SIENNA Professional. In case of a power failure the switch position and the brightness stage are stored and may be switched on when the power supply is restored. Automatic electronic overload protection and overtemperature switch-off. Two rotary switches are located on the front for address assignment: The left rotary switch defines the group address g with 16 alphabetical values from A to P. The right rotary switch defines the element address e with 16 numerical values from 0 to 15. Above it is a slide switch which acts as a configuration switch: The position AUTO1 allows the dimming of all types of lamps up to 300 watts. The position LC1 is a comfort position for LED lamps up to 150 watts which are not being dimmed down enough when set to AUTO (trailing phase angle) dependent on the construction and must therefore be forced to leading phase angle. The position AUTO2 allows the dimming of all types of lamps up to 300 watts. Increased minimum brightness compared to AUTO1. All entries and configurations can also be accessed via the mains using the PC software SIENNA Professional. In position LC1 no inductive (wound) transformers should be used. In addition, the maximum number of dimmable LED lamps can be lower than in the AUTO position dependent on the construction. Mixing of L loads (inductive loads, e.g. wound transformers) and C loads (capacitive loads, e.g. electronic transformers) is not permitted. R loads (ohmic loads, e.g. 230V incandescent lamps and halogen lamps) may be added anytime. To the left of the rotary switches is a red LED which indicates all activities. Next to it is a reset pushbutton and to the right of that is a service pin. For functions, please refer to the operating instructions. The terminals located above are plug-in terminals for conductor cross-sections of 0.2mm2 to 1.5mm².