Powerline universal dimmer actuator 1 channel with sensor input 230V

Состояние товара	Новый
Название производителя	Powerline universal dimmer actuator 1 channel with sensor input 230V
Бренд	ELTAKO
Категории	Датчики
Страна происхождения	CN
Код гармонизированной системы	8526 9200 00
Способ крепления	Монтаж заподлицо (штукатурка)
Модель	Модуль управления
Количество выходов	1
Частота	50 Hz
Шинная система KNX	No
Шинная система радио частая	No
Шинная система Powernet	Yes
С автобусным сообщением	Yes
Тип нагрузки	Универсальный
Напряжение	230 V
Другие автобусные системы	Нет
Шинная система LON	No
Вход подстанции	No
Возможно параллельное обслуживание	Yes
Локальное управление/ручное управление	Yes
Выходная мощность	600 W
со светодиодной индикацией	Yes
Повышение мощности подходит	No
Шинная система Радио KNX	No
Радио частый двунаправленный	Yes
Модуль шины съемный	No
Мин. глубина встроенной монтажной коробки	40 mm
Макс. светодиодный индикатор питания	300 W

Уровень упаковки 1	4010312316870, 4010312316870
Уровень упаковки 2	4010312316870
Уровень упаковки 3	4010312316870

Powerline universal dimmer actuator. 53x43mm, 40mm deep for mounting in 58mm switch boxes. Power MOSFET up to 300W. Automatic lamp detection. Sensor input 230V. Standby loss only 0,6 Watt. To control and dim at the same place. Universal dimmer switch for lamps up to 300W, dependent on ventilation conditions. Dimmable 230V-LED lamps and dimmable energy saving lamps ESL, additionally dependent on the lamps electronics. No minimum load. Zero passage switching with soft ON and soft OFF to protect lamps. Short-time control commands switch on/off, permanent control varies the brightness to the maximum or minimum level. A interruption of control changes the direction of dimming. The brightness level is stored on switch-off (memory). Minimum and maximum brightness can be changed with SIENNA Professional. In case of a power failure the switch position and the brightness stage are stored and may be switched on when the power supply is restored. Automatic electronic overload protection and overtemperature switch-off. Two rotary switches are located on the front for address assignment: The left rotary switch defines the group address g with 16 alphabetical values from A to P. The right rotary switch defines the element address e with 16 numerical values from 0 to 15. Above it is a slide switch which acts as a configuration switch: The position AUTO1 allows the dimming of all types of lamps up to 300 watts. The position LC1 is a comfort position for LED lamps up to 150 watts which are not being dimmed down enough when set to AUTO (trailing phase angle) dependent on the construction and must therefore be forced to leading phase angle. The position AUTO2 allows the dimming of all types of lamps up to 300 watts. Increased minimum brightness compared to AUTO1. All entries and configurations can also be accessed via the mains using the PC software SIENNA Professional. In position LC1 no inductive (wound) transformers should be used. In addition, the maximum number of dimmable LED lamps can be lower than in the AUTO position dependent on the construction. Mixing of L loads (inductive loads, e.g. wound transformers) and C loads (capacitive loads, e.g. electronic transformers) is not permitted. R loads (ohmic loads, e.g. 230V incandescent lamps and halogen lamps) may be added anytime. To the left of the rotary switches is a red LED which indicates all activities. Next to it is a reset pushbutton and to the right of that is a service pin. For functions, please refer to the operating instructions. The terminals located above are plug-in terminals for conductor cross-sections of 0.2mm2 to 1.5mm².