Register to Unlock Your Exclusive B2B Prices. Register now
DALI relay module 8A for flush-mounted box (DT7)
Laohinnas (käibemaksuta):
123,01 €
Hind kehtib kuni 2024-12-31
Hind m kohta:
123,01 €
EAN: 4010312324035
MPN: 33000007
Meie ladu:
Ei
Hankija laovaru:
Ei
Pakendi kohta:
1
Kasti kohta:
1
Kaubaaluse kohta:
N/A
Tehnilised andmed
| Toote seisukord | Uus |
| Tootja nimi | DALI relay module 8A for flush-mounted box (DT7) |
| Bränd | ELTAKO |
| Kategooriad |
Andurid |
| Päritoluriik | CN |
| Harmoneeritud süsteemi kood | 8542 3190 00 |
| Paigaldusviis | Süvistatud paigaldus (krohvi) |
| Tunnusvool | 10 A |
| Väljundvõimsus | 1000 W |
| Tunnus-talitluspinge | 230 V |
| Siinisüsteem KNX | No |
| Raadiosageduslik siinisüsteem | No |
| Siinisüsteem Powernet | No |
| Suurim lülitusvõimsus | 1000 W |
| Siiniühendusega | Yes |
| Suurim lülituskontaktide arv | 1 |
| Suurim lülitusvool | 8 A |
| Muud siinisüsteemid | Muul viisil |
| Siinisüsteem LON | No |
| C-koormus | No |
| Eri faaside ühendamine | No |
| Lokaaljuhtimine/käsijuhtimine | No |
| Kaitseaste (IP) | IP20 |
| LED näidikuga | No |
| Laiendusmoodulitega | No |
| Siinisüsteem KNX radio | No |
| Raadiosageduslik, kahesuunaline | No |
| Eemaldatav siini moodul | No |
| Max. switching power LED | 1000 W |
Pakendamise üksikasjad
| Pakkimistase 1 | 4010312324035, 4010312324035 |
Downloads
Kirjeldus
Module to control a relay contact over the DALI bus (DT7) for luminary installation and flush-mounted box. 59x33x15mm. Protection class IP20. DALI current consumption 2.7mA. Compact relay module for direct control of 230V loads over DALI. Loads without DALI input are easily integrated in a DALI circuit. Loads can be switched on/off by DALI commands. The device function complies with the standard for DALI Device Type 7 – switching function (as of Firmware 2.0). Adjustable characteristic for power-up and bus power failure. The DALI RM8 is powered over the DALI bus. No additional power supply is required. Zero passage switch-on. The module represents a bus user and is therefore addressable. Configuration via DALI Cockpit PC software. DALI functions and command set: The DALI RM8 can integrate loads on the DALI bus and can then switch them on/off. The DALI RM8 is a control device for non-dimmable loads based on the DALI specifications in IEC 62386-208 (Device Type 7). Accordingly, the switch characteristic is determined by comparing the virtual dim level (VDAP) with 4 switching thresholds. The virtual dim level (VDAP) corresponds to the dim level of a DALI electronic ballast with its corresponding characteristics (limited by MINLEVEL and MAXLEVEL, dimming speed limited by fade time and fade rate). There are 2 switching thresholds in each dimming direction and they are used for comparison with the virtual dim level. Only the applicable switching threshold for the current virtual dimming direction is evaluated. A threshold with the value MASK is inactive and is not used in the comparison. Switch-on/off delays can be implemented with fading. The DALI RM8 is powered from the DALI bus. The relay response to a bus power failure can be configured by the SystemFailureLevel (no change, ON or OFF, factory setting: ON). The power-on response after applying bus power can be set with PowerOnLevel.