DALI relay module 8A for flush-mounted box (DT7)
Noliktavas cena (bez PVN):
123,01 €
Šī cena ir spēkā līdz 2024-12-31
Cena par m:
123,01 €
EAN: 4010312324035
MPN: 33000007
Mūsu noliktava:
Nē
Piegādātāja krājumi:
Nē
Vienā iepakojumā:
1
Vienā kastē:
1
Vienā paletē:
N/A
Tehniskie dati
| Preces stāvoklis | Jauns |
| Ražotāja nosaukums | DALI relay module 8A for flush-mounted box (DT7) |
| Zīmols | ELTAKO |
| Kategorijas |
Sensori |
| Izcelsmes valsts | CN |
| Harmonizētās sistēmas kods | 8542 3190 00 |
| Montāžas metode | Iebūvējams vienā līmenī (apmetums) |
| Nominālā strāva | 10 A |
| Izejas jauda | 1000 W |
| Nominālais darba spriegums | 230 V |
| Autobusu sistēma KNX | No |
| Autobusu sistēmas radio bieži | No |
| Autobusu sistēma Powernet | No |
| Maks. pārslēgšanas jauda | 1000 W |
| Ar autobusa savienojumu | Yes |
| Maks. pārslēgšanas kontaktu skaits | 1 |
| Maks. pārslēgšanas strāva | 8 A |
| Citas autobusu sistēmas | Citi |
| Autobusu sistēma LON | No |
| Piemērots C-slodzei | No |
| Savienojamas dažādas fāzes | No |
| Vietējā darbība/rokas darbība | No |
| Aizsardzības pakāpe (IP) | IP20 |
| Ar LED indikāciju | No |
| Moduļu paplašināšana | No |
| Autobusu sistēma KNX radio | No |
| Radio bieži divvirzienu | No |
| Autobusa modulis noņemams | No |
| Maks. pārslēgšanas jaudas LED | 1000 W |
Iepakojuma informācija
| Iepakojuma līmenis 1 | 4010312324035, 4010312324035 |
Downloads
Apraksts
Module to control a relay contact over the DALI bus (DT7) for luminary installation and flush-mounted box. 59x33x15mm. Protection class IP20. DALI current consumption 2.7mA. Compact relay module for direct control of 230V loads over DALI. Loads without DALI input are easily integrated in a DALI circuit. Loads can be switched on/off by DALI commands. The device function complies with the standard for DALI Device Type 7 – switching function (as of Firmware 2.0). Adjustable characteristic for power-up and bus power failure. The DALI RM8 is powered over the DALI bus. No additional power supply is required. Zero passage switch-on. The module represents a bus user and is therefore addressable. Configuration via DALI Cockpit PC software. DALI functions and command set: The DALI RM8 can integrate loads on the DALI bus and can then switch them on/off. The DALI RM8 is a control device for non-dimmable loads based on the DALI specifications in IEC 62386-208 (Device Type 7). Accordingly, the switch characteristic is determined by comparing the virtual dim level (VDAP) with 4 switching thresholds. The virtual dim level (VDAP) corresponds to the dim level of a DALI electronic ballast with its corresponding characteristics (limited by MINLEVEL and MAXLEVEL, dimming speed limited by fade time and fade rate). There are 2 switching thresholds in each dimming direction and they are used for comparison with the virtual dim level. Only the applicable switching threshold for the current virtual dimming direction is evaluated. A threshold with the value MASK is inactive and is not used in the comparison. Switch-on/off delays can be implemented with fading. The DALI RM8 is powered from the DALI bus. The relay response to a bus power failure can be configured by the SystemFailureLevel (no change, ON or OFF, factory setting: ON). The power-on response after applying bus power can be set with PowerOnLevel.