Universal dimmer switch, Power MOSFET up to 400W

Toote seisukord	Uus
Tootja nimi	Universal dimmer switch, Power MOSFET up to 400W
Bränd	ELTAKO
Kategooriad	Lülitid
Päritoluriik	CN
Harmoneeritud süsteemi kood	8536 5080 00
Kooste ehitus	Muul viisil
Talitlusviis	Puutetundlik nupp
Koormuse liik	Universaalne
Nimipinge	230 V
Laius	45 mm
Kõrgus	45 mm
Seadme sügavus	18 mm

Pakkimistase 1	4010312108062, 4010312108062
Pakkimistase 2	4010312108062
Pakkimistase 3	4010312108062

Paigaldusviis	Süvistatud paigaldus (krohvi)
Värvus	Sinine
Halogeenivaba	Yes
Ühenduse liik	Kruviklemmid
Pinnatöötlus	Töötlemata
Materjal	Termoplastist
Materjal	Plast
Kinnitusviis	Kruviliitega
Valgustatuse mälu	Yes
Alajaama sisend	No
Serial dimmer	No
Rakendatav koos liikumisanduriga	No
Rakendatav koos edastuslülitiga	No
Rakendatav koos infrapunalülitiga	No
Rakendatav koos olemasolu indikaatoriga	No
Rakendatav koos nupplülitiga	Yes
Rakendatav koos aeglüliti/taimeriga	No
Juhtimispinge	230 V
Läbipaistev	No
Pinna liik	Matt
Südamiku ristlõige	4 mm²
Saadaval on rakenduste IFTTT sobitustugi	No
Reguleerimine, faasi väljalülitamine	No
Reguleerimine, faasi sisselülitamine	No
Sisseehitatud paigalduskarbi vähim sügavus	18 mm
Rakenduse juhtimine sinihambaga (Bluetooth)	No
Nominal power resistive load	400 W
Nominal power inductive load	400 VA
Nominal power capacitive load	400 VA
Compatible with Apple HomeKit	No
Compatible with Google Assistant	No
Compatible with Amazon Alexa	No

Without N connection, POWER MOSFET up to 400W. Standby loss 0.5 watt only. With control inputs for pushbutton light switches and light switches. With adjustable minimum brightness and ­dimming speed. Built-in device for installation. 45mm long, 45mm wide, 18mm deep. Universal dimmer switch for R, L and C loads up to 400 watt, depending on ventilation conditions. Automatic detection of load R+L or R+C. Not compatible with 230V LED and energy saving lamps, please use the EUD61NPL or the dimmer with N connection: EUD61NPN. Zero passage switching with soft start and soft OFF to protect lamps. Control voltage 230V. Min. load 20W. Short-time control commands switch on/off, permanent control varies the brightness up to the maximum level. A short interruption of control changes the direction of dimming. The brightness level is stored after switching off. In case of a power failure the switching position and the brightness level are stored. If applicable the dimmer will be switched on at the stored brightness level after the supply voltage is recovered. Automatic electronic overload protection and over-temperature switch-off. The minimum brightness level (completely dimmed down) can be adjusted with the upper rotary switch %lamp. The dimming speed can be adjusted with the lower dimming speed rotary switch. Simultaneously the soft on and soft off period is changed. If light switches cannot be replaced by pushbutton light switches, there is a separate control input for light switches. If the switch is opened briefly after closing, the light is dimmed until the next time it is opened again briefly. The dimming direction changes automatically at both peaks. The dimming direction can also be changed by opening the switch briefly twice. Switching operation for children's rooms (only if controlled by pushbutton light switch): If the light is switched on by holding down the pushbutton, it starts at the lowest brightness level after approx. 1 second and dims up slowly as long as the pushbutton is held down without modifying the last stored brightness level. Snooze function (only if controlled by pushbutton light switch): With a double impulse the lighting is dimmed down from the current dimming position to the minimum brightness level and switched off. The current dimming position as well as the adjustable minimum brightness level determine the dimming time (max. = 60 minutes) which can be reduced as required. It can be switched off at any time by short-time control commands during the lighting is dimmed down. Holding down the pushbutton during the dimming down process dims up and stops the snooze function. Without N connection, therefore suitable for mounting directly behind the pushbutton light switch or light switch, even if no N wire is available. Mixing of L loads (inductive loads, e.g. wound transformers) and C loads (capacitive loads, e.g. electronic transformers) is not permitted. R loads (ohmic loads, e.g. 230V incandescent lamps and halogen lamps) may be added anytime.