Universal dimmer switch, Power MOSFET up to 400W

Состояние товара	Новый
Название производителя	Universal dimmer switch, Power MOSFET up to 400W
Бренд	ELTAKO
Категории	Выключатели
Страна происхождения	CN
Код гармонизированной системы	8536 5080 00
Устройство сборки	Другое
Метод работы	Сенсорная кнопка управления
Тип нагрузки	Универсальный
Номинальное напряжение	230 V
Ширина устройства	45 mm
Высота устройства	45 mm
Глубина устройства	18 mm

Уровень упаковки 1	4010312108062, 4010312108062
Уровень упаковки 2	4010312108062
Уровень упаковки 3	4010312108062

Способ крепления	Монтаж заподлицо (штукатурка)
Цвет	Синий
Без галогена	Yes
Тип соединения	Винтовая клемма
Защита поверхности	Необработанный
Качество материала	Термопластик
Материал	Пластик
Тип крепления	Крепление с винтом
Память светового значения	Yes
Вход подстанции	No
Серийный диммер	No
Применяется с датчиком движения	No
Применимо с кнопкой передачи	No
Применимо с инфракрасной кнопкой	No
Применяется с индикатором присутствия	No
Применимо с кнопкой	Yes
Применимо с таймером/таймером	No
Управляющее напряжение	230 V
Прозрачный	No
Отделка поверхности	Матовый
Сечение жилы	4 mm²
Доступна поддержка IFTTT	No
Отсечка фазы диммирования	No
Отключение фазы диммирования	No
Мин. глубина встроенной монтажной коробки	18 mm
Управление приложением через Bluetooth	No
Номинальная мощность активной нагрузки	400 W
Номинальная мощность индуктивной нагрузки	400 VA
Номинальная мощность емкостной нагрузки	400 VA
Совместимость с Apple HomeKit	No
Совместимость с Google Ассистент	No
Совместимость с Amazon Alexa	No

Without N connection, POWER MOSFET up to 400W. Standby loss 0.5 watt only. With control inputs for pushbutton light switches and light switches. With adjustable minimum brightness and ­dimming speed. Built-in device for installation. 45mm long, 45mm wide, 18mm deep. Universal dimmer switch for R, L and C loads up to 400 watt, depending on ventilation conditions. Automatic detection of load R+L or R+C. Not compatible with 230V LED and energy saving lamps, please use the EUD61NPL or the dimmer with N connection: EUD61NPN. Zero passage switching with soft start and soft OFF to protect lamps. Control voltage 230V. Min. load 20W. Short-time control commands switch on/off, permanent control varies the brightness up to the maximum level. A short interruption of control changes the direction of dimming. The brightness level is stored after switching off. In case of a power failure the switching position and the brightness level are stored. If applicable the dimmer will be switched on at the stored brightness level after the supply voltage is recovered. Automatic electronic overload protection and over-temperature switch-off. The minimum brightness level (completely dimmed down) can be adjusted with the upper rotary switch %lamp. The dimming speed can be adjusted with the lower dimming speed rotary switch. Simultaneously the soft on and soft off period is changed. If light switches cannot be replaced by pushbutton light switches, there is a separate control input for light switches. If the switch is opened briefly after closing, the light is dimmed until the next time it is opened again briefly. The dimming direction changes automatically at both peaks. The dimming direction can also be changed by opening the switch briefly twice. Switching operation for children's rooms (only if controlled by pushbutton light switch): If the light is switched on by holding down the pushbutton, it starts at the lowest brightness level after approx. 1 second and dims up slowly as long as the pushbutton is held down without modifying the last stored brightness level. Snooze function (only if controlled by pushbutton light switch): With a double impulse the lighting is dimmed down from the current dimming position to the minimum brightness level and switched off. The current dimming position as well as the adjustable minimum brightness level determine the dimming time (max. = 60 minutes) which can be reduced as required. It can be switched off at any time by short-time control commands during the lighting is dimmed down. Holding down the pushbutton during the dimming down process dims up and stops the snooze function. Without N connection, therefore suitable for mounting directly behind the pushbutton light switch or light switch, even if no N wire is available. Mixing of L loads (inductive loads, e.g. wound transformers) and C loads (capacitive loads, e.g. electronic transformers) is not permitted. R loads (ohmic loads, e.g. 230V incandescent lamps and halogen lamps) may be added anytime.