Universal dimmer switch without N connection, especially for LED Power, MOSFET up to 200W

Toote seisukord	Uus
Tootja nimi	Universal dimmer switch without N connection, especially for LED Power, MOSFET up to 200W
Bränd	ELTAKO
Kategooriad	Lülitid
Päritoluriik	CN
Harmoneeritud süsteemi kood	8536 5080 00
Kooste ehitus	Muul viisil
Talitlusviis	Puutetundlik nupp
Koormuse liik	Universaalne
Nimipinge	230 V
Laius	45 mm
Kõrgus	45 mm
Seadme sügavus	18 mm
Max. switching power LED	200 W

Pakkimistase 1	4010312109618, 4010312109618
Pakkimistase 2	4010312109618
Pakkimistase 3	4010312109618

Paigaldusviis	Süvistatud paigaldus (krohvi)
Värvus	Sinine
Halogeenivaba	Yes
Ühenduse liik	Kruviklemmid
Pinnatöötlus	Töötlemata
Materjal	Termoplastist
Materjal	Plast
Kinnitusviis	Kruviliitega
Valgustatuse mälu	Yes
Alajaama sisend	No
Serial dimmer	No
Rakendatav koos liikumisanduriga	No
Rakendatav koos edastuslülitiga	No
Rakendatav koos infrapunalülitiga	No
Rakendatav koos olemasolu indikaatoriga	No
Rakendatav koos nupplülitiga	Yes
Rakendatav koos aeglüliti/taimeriga	No
Juhtimispinge	230 V
Läbipaistev	No
Pinna liik	Matt
Südamiku ristlõige	4 mm²
Saadaval on rakenduste IFTTT sobitustugi	No
Reguleerimine, faasi väljalülitamine	Yes
Reguleerimine, faasi sisselülitamine	Yes
Sisseehitatud paigalduskarbi vähim sügavus	18 mm
Rakenduse juhtimine sinihambaga (Bluetooth)	No
Nominal power resistive load	200 W
Nominal power capacitive load	200 VA
Compatible with Apple HomeKit	No
Compatible with Google Assistant	No
Compatible with Amazon Alexa	No

Without N connection, POWER MOSFET up to 200W. Standby loss 0.5 watt only. With control inputs for pushbutton light switches and light switches. With adjustable minimum brightness, dimming technology and dimming speed. For installation. 45mm long, 45mm wide, 18mm deep. Universal dimmer switch for R and C loads up to 200W, depending on ventilation conditions. Dimmable 230V LED lamps and energy saving lamps ESL in trailing edge mode up to 200W or up to 40W in leading edge mode, depending on ventilation conditions. If 230V LED lamps are lightly glowing when they are turned off, a GLE base load must be installed parallel to the lamp. It is not permited to connect L loads (inductive loads, like wounded transfomers). Zero passage switching with soft start and soft OFF to protect lamps. Control voltage, supply ­voltage and switching voltage 230V. Min. load 4W. Short-time control commands switch on/off, permanent control varies the brightness up to the maximum level. A short interruption of control changes the direction of dimming. The brightness level is stored after switching off (memory). It is possible to deactivate the memory function by turning 3 times the upper rotary switch to the right stop (max), then it is compatible with ESL. To re­activate the memory function (factory setting), turn the upper rotary switch 3 times to the left stop (min). In case of a power failure the switching position and the brightness level are stored, and will switch on after the failure if applicable. Automatic electronic overload protection and over-temperature switch-off. The minimum brightness level (completely dimmed down) can be adjusted with the upper rotary switch %lamp. The lower rotary switch allows to choose between the both dimming technologies, P-AN leading or P-AB trailing edge and to change the dimming speed. Simultaneously the duration of soft on and soft off will be adjusted. If light switches cannot be replaced by pushbutton light switches, there is a separate control input for light switches: If the switch is opened briefly after closing, the light is dimmed until the next time it is opened again briefly. The dimming direction changes automatically at both peaks. The dimming direction can also be changed by opening the switch briefly twice. Switching operation for children's rooms (only if controlled by pushbutton light switch): If the light is switched on by holding down the pushbutton, it starts at the lowest brightness level after approx. 1 second and dims up slowly as long as the pushbutton is held down without modifying the last stored brightness level. Snooze function (only if controlled by pushbutton light switch): With a double impulse the lighting is dimmed down from the current dimming position to the minimum brightness level and switched off. The current dimming position as well as the adjustable minimum brightness level determine the dimming time (max. = 60 minutes) which can be reduced as required. It can be switched off at any time by short-time control commands during the lighting is dimmed down. Holding down the pushbutton during the dimming down process dims up and stops the snooze function. Without N connection, therefore suitable for mounting directly behind the pushbutton light switch or light switch, even if no N wire is available.