Universal dimmer switch without N connection, especially for LED Power, MOSFET up to 200W

Состояние товара	Новый
Название производителя	Universal dimmer switch without N connection, especially for LED Power, MOSFET up to 200W
Бренд	ELTAKO
Категории	Выключатели
Страна происхождения	CN
Код гармонизированной системы	8536 5080 00
Устройство сборки	Другое
Метод работы	Сенсорная кнопка управления
Тип нагрузки	Универсальный
Номинальное напряжение	230 V
Ширина устройства	45 mm
Высота устройства	45 mm
Глубина устройства	18 mm
Макс. светодиодный индикатор питания	200 W

Уровень упаковки 1	4010312109618, 4010312109618
Уровень упаковки 2	4010312109618
Уровень упаковки 3	4010312109618

Способ крепления	Монтаж заподлицо (штукатурка)
Цвет	Синий
Без галогена	Yes
Тип соединения	Винтовая клемма
Защита поверхности	Необработанный
Качество материала	Термопластик
Материал	Пластик
Тип крепления	Крепление с винтом
Память светового значения	Yes
Вход подстанции	No
Серийный диммер	No
Применяется с датчиком движения	No
Применимо с кнопкой передачи	No
Применимо с инфракрасной кнопкой	No
Применяется с индикатором присутствия	No
Применимо с кнопкой	Yes
Применимо с таймером/таймером	No
Управляющее напряжение	230 V
Прозрачный	No
Отделка поверхности	Матовый
Сечение жилы	4 mm²
Доступна поддержка IFTTT	No
Отсечка фазы диммирования	Yes
Отключение фазы диммирования	Yes
Мин. глубина встроенной монтажной коробки	18 mm
Управление приложением через Bluetooth	No
Номинальная мощность активной нагрузки	200 W
Номинальная мощность емкостной нагрузки	200 VA
Совместимость с Apple HomeKit	No
Совместимость с Google Ассистент	No
Совместимость с Amazon Alexa	No

Without N connection, POWER MOSFET up to 200W. Standby loss 0.5 watt only. With control inputs for pushbutton light switches and light switches. With adjustable minimum brightness, dimming technology and dimming speed. For installation. 45mm long, 45mm wide, 18mm deep. Universal dimmer switch for R and C loads up to 200W, depending on ventilation conditions. Dimmable 230V LED lamps and energy saving lamps ESL in trailing edge mode up to 200W or up to 40W in leading edge mode, depending on ventilation conditions. If 230V LED lamps are lightly glowing when they are turned off, a GLE base load must be installed parallel to the lamp. It is not permited to connect L loads (inductive loads, like wounded transfomers). Zero passage switching with soft start and soft OFF to protect lamps. Control voltage, supply ­voltage and switching voltage 230V. Min. load 4W. Short-time control commands switch on/off, permanent control varies the brightness up to the maximum level. A short interruption of control changes the direction of dimming. The brightness level is stored after switching off (memory). It is possible to deactivate the memory function by turning 3 times the upper rotary switch to the right stop (max), then it is compatible with ESL. To re­activate the memory function (factory setting), turn the upper rotary switch 3 times to the left stop (min). In case of a power failure the switching position and the brightness level are stored, and will switch on after the failure if applicable. Automatic electronic overload protection and over-temperature switch-off. The minimum brightness level (completely dimmed down) can be adjusted with the upper rotary switch %lamp. The lower rotary switch allows to choose between the both dimming technologies, P-AN leading or P-AB trailing edge and to change the dimming speed. Simultaneously the duration of soft on and soft off will be adjusted. If light switches cannot be replaced by pushbutton light switches, there is a separate control input for light switches: If the switch is opened briefly after closing, the light is dimmed until the next time it is opened again briefly. The dimming direction changes automatically at both peaks. The dimming direction can also be changed by opening the switch briefly twice. Switching operation for children's rooms (only if controlled by pushbutton light switch): If the light is switched on by holding down the pushbutton, it starts at the lowest brightness level after approx. 1 second and dims up slowly as long as the pushbutton is held down without modifying the last stored brightness level. Snooze function (only if controlled by pushbutton light switch): With a double impulse the lighting is dimmed down from the current dimming position to the minimum brightness level and switched off. The current dimming position as well as the adjustable minimum brightness level determine the dimming time (max. = 60 minutes) which can be reduced as required. It can be switched off at any time by short-time control commands during the lighting is dimmed down. Holding down the pushbutton during the dimming down process dims up and stops the snooze function. Without N connection, therefore suitable for mounting directly behind the pushbutton light switch or light switch, even if no N wire is available.