Registreeru, et avada oma eksklusiivsed B2B hinnad ja alustada ostlemist. Registreeru kohe!
Powerline TLZ actuator 1 channel with sensor input 230V
Laos: Ei
Hankija laovaru: Ei
Minimaalne tellimuse kogus: 1
Hind (ilma KM-ta):
94,43 €
EAN: 4010312316702
MPN: 31100004
Pakend: 1
Technical Information
| Toote seisukord | Uus |
| Tootja nimi | Powerline TLZ actuator 1 channel with sensor input 230V |
| Bränd | ELTAKO |
| Kategooriad |
Andurid |
| Päritoluriik | CN |
| Harmoneeritud süsteemi kood | 8526 9200 00 |
| Paigaldusviis | Süvistatud paigaldus (krohvi) |
| Väljundvõimsus | 2000 W |
| Siinisüsteem KNX | No |
| Raadiosageduslik siinisüsteem | No |
| Siinisüsteem Powernet | Yes |
| Suurim lülitusvõimsus | 2000 W |
| Siiniühendusega | Yes |
| Suurim lülituskontaktide arv | 1 |
| Suurim lülitusvool | 10 A |
| Muud siinisüsteemid | Puudub |
| Siinisüsteem LON | No |
| C-koormus | Yes |
| Eri faaside ühendamine | No |
| Lokaaljuhtimine/käsijuhtimine | - |
| LED näidikuga | Yes |
| Laiendusmoodulitega | No |
| Siinisüsteem KNX radio | No |
| Raadiosageduslik, kahesuunaline | - |
| Eemaldatav siini moodul | No |
| Sisseehitatud paigalduskarbi vähim sügavus | 25 mm |
| Max. switching power LED | 400 W |
Pakendamise üksikasjad
| Pakkimistase 1 | 4010312316702, 4010312316702 |
| Pakkimistase 2 | 4010312316702 |
| Pakkimistase 3 | 4010312316702 |
Allalaadimised
Kirjeldus
Powerline TLZ (staircase time switch) actuator with 1 channel. 53x43mm, 25mm deep for mounting in 58mm switch boxes. Off delay settable from 1 minute to 120 minutes. Switch-off early warning settable. 1 NO contact not potential free 10A/250V AC, incandescent lamps 2000 watts. Sensor input 230V. Standby loss only 0,5 watt. To control and switch at the same place. Two rotary switches are located on the front for address assignment: The left rotary switch defines the group address g with 16 alphabetical values from A to P. The right rotary switch determines the off-delay time. Above it is a slide switch which acts as a configuration switch with positions 0, 1 and 2. Position 0: Pushbutton at sensor input with subsequent switching. Position 1: Same as Position 0 but with switch-off early warning. Position 2: A change-over switch is evaluated as a pushbutton. All entries and configurations can also be accessed via the mains using the PC software SIENNA Professional. To the left of the rotary switches is a red LED which indicates all activities. Next to it is a reset pushbutton and to the right of that is a service pin. For functions, please refer to the operating instructions. The terminals located above are plug-in terminals for conductor cross-sections of 0.2mm² to 1.5mm².