Powerline TLZ actuator 1 channel with sensor input 230V
Noliktavas cena (bez PVN):
94,43 €
Šī cena ir spēkā līdz 2024-12-31
Cena par m:
94,43 €
EAN: 4010312316702
MPN: 31100004
Mūsu noliktava:
Nē
Piegādātāja krājumi:
Nē
Vienā iepakojumā:
1
Vienā kastē:
1
Vienā paletē:
N/A
Tehniskie dati
| Preces stāvoklis | Jauns |
| Ražotāja nosaukums | Powerline TLZ actuator 1 channel with sensor input 230V |
| Zīmols | ELTAKO |
| Kategorijas |
Sensori |
| Izcelsmes valsts | CN |
| Harmonizētās sistēmas kods | 8526 9200 00 |
| Montāžas metode | Iebūvējams vienā līmenī (apmetums) |
| Izejas jauda | 2000 W |
| Autobusu sistēma KNX | No |
| Autobusu sistēmas radio bieži | No |
| Autobusu sistēma Powernet | Yes |
| Maks. pārslēgšanas jauda | 2000 W |
| Ar autobusa savienojumu | Yes |
| Maks. pārslēgšanas kontaktu skaits | 1 |
| Maks. pārslēgšanas strāva | 10 A |
| Citas autobusu sistēmas | Nav |
| Autobusu sistēma LON | No |
| Piemērots C-slodzei | Yes |
| Savienojamas dažādas fāzes | No |
| Vietējā darbība/rokas darbība | - |
| Ar LED indikāciju | Yes |
| Moduļu paplašināšana | No |
| Autobusu sistēma KNX radio | No |
| Radio bieži divvirzienu | - |
| Autobusa modulis noņemams | No |
| Min. iebūvētās instalācijas kastes dziļums | 25 mm |
| Maks. pārslēgšanas jaudas LED | 400 W |
Iepakojuma informācija
| Iepakojuma līmenis 1 | 4010312316702, 4010312316702 |
| Iepakojuma līmenis 2 | 4010312316702 |
| Iepakojuma līmenis 3 | 4010312316702 |
Downloads
Apraksts
Powerline TLZ (staircase time switch) actuator with 1 channel. 53x43mm, 25mm deep for mounting in 58mm switch boxes. Off delay settable from 1 minute to 120 minutes. Switch-off early warning settable. 1 NO contact not potential free 10A/250V AC, incandescent lamps 2000 watts. Sensor input 230V. Standby loss only 0,5 watt. To control and switch at the same place. Two rotary switches are located on the front for address assignment: The left rotary switch defines the group address g with 16 alphabetical values from A to P. The right rotary switch determines the off-delay time. Above it is a slide switch which acts as a configuration switch with positions 0, 1 and 2. Position 0: Pushbutton at sensor input with subsequent switching. Position 1: Same as Position 0 but with switch-off early warning. Position 2: A change-over switch is evaluated as a pushbutton. All entries and configurations can also be accessed via the mains using the PC software SIENNA Professional. To the left of the rotary switches is a red LED which indicates all activities. Next to it is a reset pushbutton and to the right of that is a service pin. For functions, please refer to the operating instructions. The terminals located above are plug-in terminals for conductor cross-sections of 0.2mm² to 1.5mm².