dimm.act. 1-g 500 W/VA KNX DRA

Состояние товара	Новый
Название производителя	dimm.act. 1-g 500 W/VA KNX DRA
Бренд	Gira
Категории	Датчики
Страна происхождения	DE
Код гармонизированной системы	8536 4900 00
Способ крепления	DRA (адаптер для установки на DIN-рейку)
Модель	Привод регулировки яркости
Количество выходов	1
Частота	50-60 Hz
Шинная система KNX	Yes
Шинная система радио частая	No
Шинная система Powernet	No
С автобусным сообщением	Yes
Тип нагрузки	Универсальный
Макс. управляющий ток	NA mA
Напряжение	230 V
Ширина в количестве модульных интервалов	4
Другие автобусные системы	Нет
Шинная система LON	No
Вход подстанции	Yes
Возможно параллельное обслуживание	No
Локальное управление/ручное управление	Yes
Выходная мощность	20-500 W
Степень защиты (IP)	IP20
со светодиодной индикацией	No
Повышение мощности подходит	No
Шинная система Радио KNX	No
Радио частый двунаправленный	-
Модуль шины съемный	-
Мин. глубина встроенной монтажной коробки	0 mm
Макс. светодиодный индикатор питания	50 W

Уровень упаковки 1

4010337082200

Dimming actuator, 1-gang for KNX 20 -500 W VA DRA plus Features: Dim actuator with integrated bus coupler. Switching and dimming of light bulbs, HV halogen lamps, dimmable HV-LED lamps, dimmable compact fluorescent lamps, dimmable inductive transformers with LV halogen or NV-LED lamps, dimmable electronic transformers with LV halogen or NV-LED lamps. Automatic or manual selection of dimming principle according to load. Idle-state, short-circuit, and excess temperature-proof Manual actuation of the outputs independent of the bus (building site operation also possible). The dimming actuator, 1-gang can also be used as speed regulator for speed control of single-phase electric motors. Building site operation: Outputs can be operated manually without bus voltage with operating voltage only. Functions: Independent control of the dimming channels. For building site operation, outputs can be operated manually without bus voltage with operating voltage only. Central switching function for control of all dimming channels. Delay for actively transmitted feedback messages following bus voltage recovery. Load type and dimming method can be configured: Universal (with automatic calibration procedure), electronic transformer LV LED (capacitive phase cut), conventional transformer LV LED (inductive phase cut), HV LED (phase cut) or HV LED (phase cut). Feedback for "switching" and "brightness value". Dimmable brightness range can be set. Dimming behaviour and dimming characteristics can be parameterised. Switch-on behaviour for a relative dimming command can be parameterised. Bulb-saving switch-on and switch-off Automatic setting and scaling of the dimmable brightness range when using universal power boosters. The performance of a dimming channel in the "OFF" state during reception of a relative dimming command can be parameterised (switching and dimming or no response). Alarm telegrams for short circuit, overload, and load failure. Feedback of connected load type. Block function or forced setting function can be parameterised for each output. Time functions (switch-on off delay, staircase light function). Staircase light function with advance warning function via time-controlled reduction of lighting or activation of permanent lighting. Linking function and up to eight scenes per dimming channel possible. Elapsed operating time meter for recording switch-on time. Reactions after bus voltage failure and recovery can be set. Notes : Power extension using Gira power boosters. Installation on DIN top-hat rail. VDE approval in accordance with EN 60669-1, EN 60669-2-1.