Technical Information
Состояние товара |
Новый |
Название производителя |
Analogue settable time relay with clock generator, 1 CO contact 10A |
Бренд |
ELTAKO
|
Категории |
Реле
|
Страна происхождения |
CN |
Код гармонизированной системы |
8536 4900 00
|
Способ крепления |
DIN-рейка |
Функция |
Таймер запуска с импульсом |
Встроенная высота |
58 mm |
Тип возбуждения |
Аналоговый с одной функцией |
Ширина в количестве модульных интервалов |
1 |
Количество переключателей |
1 |
Управляющее напряжение 1 |
8-230 V |
Тип управляющего напряжения 1 |
AC/DC |
Напряжение управления частотой 1 |
50 Hz |
Тип напряжения питания |
AC/DC |
Напряжение питания |
8-230 V |
1-я интервальная единица |
Минуты/часы |
1-й интервал |
0.1-40 |
Коммутационная способность ламп накаливания |
2000 W |
Коммутационная способность Люминесцентная лампа DUO |
1000 VA |
Коммутационная способность индуктивной люминесцентной лампы |
1000 VA |
Коммутационная способность люминесцентной лампы параллельно |
500 VA |
Количество контактов как нормально закрытый контакт |
0 |
Количество контактов как нормально разомкнутый контакт |
0 |
Сведения об упаковке
Уровень упаковки 1 |
4010312603116, 4010312603116 |
Уровень упаковки 2 |
4010312603116 |
Уровень упаковки 3 |
4010312603116 |
Загрузки
Описание
Clock generator starting with impulse, 1 CO contact potential free 10A/250V AC. 230V LED lamps up to 200W, incandescent lamps 2000W*. Standby loss 0.02-0.4 watt only. Modular devices for DIN-EN 60715 TH35 rail mounting. 1 module = 18mm wide, 58mm deep. T1 and T2 can be set separately by a second multiplier while the time base remains the same. With the Eltako Duplex technology (DX) the normally potential-free contacts can still switch in zero passage when switching 230V AC 50Hz and therefore drastically reduce wear. Simply connect the neutral conductor to the terminal (N) and L to 15(L) for this. This gives an additional standby consumption of only 0.1 Watt. Universal control voltage 8 to 230V UC. Supply voltage same as the control voltage. Time setting between 0.1 seconds and 40 hours. By using a bistable relay coil power loss and heating is avoided even in the on mode. The switched consumer may not be connected to the mains before the short automatic synchronisation after installation has terminated. The LED below the big rotary switch indicates the contact position while time-out is in progress. It blinks while the relay contact 15-18 is open (15-16 closed), and is continuously ON as long as the relay contact 15-18 is closed (15-16 open). The time base T is selected by means of the middle, latching rotary switch T. Time-base figures available are 0.1 seconds, 0.5 seconds, 2 seconds, 5 seconds, 1 minute, 2 minutes, 5 minutes, 1 hour, 2 hours and 4 hours. The total time is obtained by multiplying the timebase by the multiplier. The multiplier xT is set on the upper, latching rotary switch xT and is in the range from 1 to 10. Thus, time settings can be selected in the range from 0.1 seconds (time base 0.1 seconds and multiplier 1) and 40 hours (time base 4 hours and multiplier 10). * The maximum load can be used starting at a delay time or clock cycle of 5 minutes. The maximum load will be reduced for shorter times as follows: up to 2 seconds 15%, up to 2 minutes 30%, up to 5 minutes 60%.