Universal dimmer switch, Power MOSFET up to 300W and switching-off relay

Item condition	New
Brand	ELTAKO
Categories	Switches
Country of origin	CN
Harmonized System Code	8536 5080 00
Assembly arrangement	Other
Method of operation	Touch control button
Frequency	50 Hz
Type of load	Universal
Nominal voltage	230 V
Device width	18 mm
Device height	58 mm
Device depth	66 mm
Max. switching power LED	300 W

Packing level 1	4010312108086, 4010312108086
Packing level 2	4010312108086
Packing level 3	4010312108086

Mounting method	DRA (DIN-rail adapter)
Colour	Blue
Halogen free	Yes
Connection type	Screwed terminal
Surface protection	Other
Material quality	Thermoplastic
Material	Plastic
Type of fastening	Other
Light value memory	Yes
Substation input	No
Serial dimmer	No
Applicable with movement sensor	No
Applicable with transmission button	No
Applicable with infrared button	No
Applicable with presence indicator	No
Applicable with button	Yes
Applicable with time switch/timer	No
Control voltage	8-230 V
Transparent	No
Surface finishing	Matt
Core cross section	6 mm²
IFTTT support available	No
Dimming phase cut-off	No
Dimming phase cut-on	No
App control via Bluetooth	No
Nominal power resistive load	300 W
Nominal power inductive load	300 VA
Nominal power capacitive load	300 VA
Compatible with Apple HomeKit	No
Compatible with Google Assistant	No
Compatible with Amazon Alexa	No

Universal dimmer switch. Power MOSFET up to 300W. Automatic lamp ­detection. Standby loss 0.1 watt only. With adjustable minimum brightness and dimming speed. With switching operation for children's rooms and snooze function. Modular device for DIN EN 60715 TH35 rail mounting. 1 module = 18mm wide, 58mm deep. Universal dimmer switch for lamps up to 300W, depending on ventilation conditions, dimmable 230V LED lamps and dimmable energy saving lamps (ESL) are also dependent on the lamp electronics. Zero passage switching with soft start and soft OFF to protect lamps. Supply voltage and switching voltage 230V. Short-time control commands switch on/off, permanent control varies the brightness to the maximum level. An interruption of control changes the direction of dimming. The setting of the brightness level is stored after switching off. In case of a power failure the switching position and the brightness level are stored. If applicable the dimmer will be switched on at the stored brightness level after the supply voltage is recovered. Automatic electronic overload protection and over-temperature switch-off. With integrated switching-off relay for the mains disconnection of switched circuits. The control pushbutton(s) of the room are connected via low voltage control wires to the terminals T1 and T2 of the EUD12F (field-free internal DC voltage). The permanent power supply must be connected directly to a phase conductor ahead of the mains disconnection relay FR12-230V. Due to this, the complete function remains but the leads to the lamps is disconnected by means of the switching-off relay. A glow lamp current is not permitted. The minimum brightness level (completely dimmed down) can be adjusted with the upper rotary switch %lamp, e.g. for dimmable energy saving lamps. You can dim all lamp types in automatic mode. Use the lower dimming speed rotary switch to set the dimming speed in seven steps in automatic mode. +ESL is a convenience setting for energy saving lamps which must be switched on at high voltage for design reasons so that they can also be switched back on cold in dimmed state. -ESL is a convenience setting for energy saving lamps which cannot be switched back on in dimmed state for design reasons. This is why memory is switched off in this position. No inductive (wound) transformers may be used in +ESL and -ESL settings. In addition the maximum number of dimmable energy saving lamps may be lower than in automatic mode for design reasons. With special switching operation for children's rooms: If the light is switched on by holding down the pushbutton, it starts at the lowest brightness level after approx. 1 second and dims up slowly as long as the pushbutton is held down without modifying the last stored brightness level. Snooze function: With a double impulse the lighting is dimmed down from the current dimming position to the minimum brightness level and switched off. The current dimming position as well as the adjustable minimum brightness level determine the dimming time (max. = 60 minutes) which can be reduced as required. It can be switched off at any time by short-time control commands during the lighting is dimmed down. Holding down the pushbutton during the dimming down process dims up and stops the snooze function. Mixing of L loads (inductive loads, e.g. wound transformers) and C loads (capacitive loads, e.g. electronic transformers) is not permitted. R loads (ohmic loads, e.g. 230V incandescent lamps and halogen lamps) may be added anytime. Mixing of L loads and C loads is possible with the dimmer switch EUD12D in ­connection with capacity enhancer LUD12.